化工环保
化工環保
화공배보
ENVIRONMENTAL PROTECTION OF CHEMICAL INDUSTRY
2012年
1期
16-20
,共5页
李兰%杨旭%杨德敏%徐燕%万用波
李蘭%楊旭%楊德敏%徐燕%萬用波
리란%양욱%양덕민%서연%만용파
聚合物驱废水%聚丙烯酰胺%芬顿试剂%次氯酸钙%二氧化氯%黏度%废水处理
聚閤物驅廢水%聚丙烯酰胺%芬頓試劑%次氯痠鈣%二氧化氯%黏度%廢水處理
취합물구폐수%취병희선알%분돈시제%차록산개%이양화록%점도%폐수처리
分别采用UV-Fenton试剂氧化法、次氯酸钙氧化法和二氧化氯氧化法处理模拟聚合物驱废水,考察了各工艺条件对废水降黏效果的影响.实验结果表明:在初始废水pH为7、反应温度为50℃、反应时间为20min的条件下,UV-Fenton试剂氧化法适宜的H2O2加入量为1 mmol/L,n(H2O2)∶n(Fe2+)=l0,处理后废水降黏率达65.7%;次氯酸钙氧化法适宜的次氯酸钙加入量为500 mg/L,处理后废水降黏率达81.7%;二氧化氯氧化法适宜的二氧化氯加入量为100 mg/L,处理后废水降黏率为40.9%.3种氧化法对模拟聚合物驱废水的降黏率大小顺序为:次氯酸钙氧化法>UV-Fenton试剂氧化法>二氧化氯氧化法.
分彆採用UV-Fenton試劑氧化法、次氯痠鈣氧化法和二氧化氯氧化法處理模擬聚閤物驅廢水,攷察瞭各工藝條件對廢水降黏效果的影響.實驗結果錶明:在初始廢水pH為7、反應溫度為50℃、反應時間為20min的條件下,UV-Fenton試劑氧化法適宜的H2O2加入量為1 mmol/L,n(H2O2)∶n(Fe2+)=l0,處理後廢水降黏率達65.7%;次氯痠鈣氧化法適宜的次氯痠鈣加入量為500 mg/L,處理後廢水降黏率達81.7%;二氧化氯氧化法適宜的二氧化氯加入量為100 mg/L,處理後廢水降黏率為40.9%.3種氧化法對模擬聚閤物驅廢水的降黏率大小順序為:次氯痠鈣氧化法>UV-Fenton試劑氧化法>二氧化氯氧化法.
분별채용UV-Fenton시제양화법、차록산개양화법화이양화록양화법처리모의취합물구폐수,고찰료각공예조건대폐수강점효과적영향.실험결과표명:재초시폐수pH위7、반응온도위50℃、반응시간위20min적조건하,UV-Fenton시제양화법괄의적H2O2가입량위1 mmol/L,n(H2O2)∶n(Fe2+)=l0,처리후폐수강점솔체65.7%;차록산개양화법괄의적차록산개가입량위500 mg/L,처리후폐수강점솔체81.7%;이양화록양화법괄의적이양화록가입량위100 mg/L,처리후폐수강점솔위40.9%.3충양화법대모의취합물구폐수적강점솔대소순서위:차록산개양화법>UV-Fenton시제양화법>이양화록양화법.