吉林化工学院学报
吉林化工學院學報
길림화공학원학보
JOURNAL OF JILIN INSTITUTE OF CHEMICAL TECHNOLOGY
2011年
9期
61-64
,共4页
杨凯钧%左春柽%丁发喜%王克军%吕海武%曹倩倩%王吉顺
楊凱鈞%左春檉%丁髮喜%王剋軍%呂海武%曹倩倩%王吉順
양개균%좌춘정%정발희%왕극군%려해무%조천천%왕길순
电火花线切割%微通道散热器%聚光太阳能电池
電火花線切割%微通道散熱器%聚光太暘能電池
전화화선절할%미통도산열기%취광태양능전지
wire electrical discharge machine microchannel heat sink concentrated solar cells. Key words: Wire electrical discharge machining heat sink concentrated photovoltaic
微通道散热器的加工是微通道散热器的核心问题之一,越来越受到广泛的关注.目前,研究人员在加工长度1000~5000 um、宽度5~500 um范围内,可以达到加工的要求,而长度大于此范围的加工工艺实现比较困难.针对此问题,本文采用数控电火花线切割方法,通过研究线电极补偿、脉宽、脉冲间隔等主要加工参数对微通道成型尺寸的影响,通过实验对比分析确定合理的加工参数以及稳定的加工条件.结果表明,加工长度为94 000 um的微通道,在线电极参数为0.77 um,脉冲宽度为28 us,间隔为9 us的前提下,所得到的微通道的宽度在250~280 um范围内.
微通道散熱器的加工是微通道散熱器的覈心問題之一,越來越受到廣汎的關註.目前,研究人員在加工長度1000~5000 um、寬度5~500 um範圍內,可以達到加工的要求,而長度大于此範圍的加工工藝實現比較睏難.針對此問題,本文採用數控電火花線切割方法,通過研究線電極補償、脈寬、脈遲間隔等主要加工參數對微通道成型呎吋的影響,通過實驗對比分析確定閤理的加工參數以及穩定的加工條件.結果錶明,加工長度為94 000 um的微通道,在線電極參數為0.77 um,脈遲寬度為28 us,間隔為9 us的前提下,所得到的微通道的寬度在250~280 um範圍內.
미통도산열기적가공시미통도산열기적핵심문제지일,월래월수도엄범적관주.목전,연구인원재가공장도1000~5000 um、관도5~500 um범위내,가이체도가공적요구,이장도대우차범위적가공공예실현비교곤난.침대차문제,본문채용수공전화화선절할방법,통과연구선전겁보상、맥관、맥충간격등주요가공삼수대미통도성형척촌적영향,통과실험대비분석학정합리적가공삼수이급은정적가공조건.결과표명,가공장도위94 000 um적미통도,재선전겁삼수위0.77 um,맥충관도위28 us,간격위9 us적전제하,소득도적미통도적관도재250~280 um범위내.
Processing of microchannel heat sink is one of the core problems of heat sinks.Currently,when processing microchannel heat sink,1 000~5 000 um in length and 5~100 um in width,reseachers can achieve the required processing,as for the processing of micro mechanical bigger in range,there have been no reports concerned.Considering this.According to the influence of the line electrode compensation,pulse width pulse gap parameters on the dimension precision processing,this paper presents Wire electrical discharge machining to solve microchannel processing,and analysis the influence of reasonable set of processing parameters and the stability of the processing.As is shown the processing of micro-channel 94 000 m in length,in the following parameters,the wire electrode parameters: 0.77 m,pulse width: 28,gap:9will result in a microchannel 250~280 um in width.