塑性工程学报
塑性工程學報
소성공정학보
JOURNAL OF PLASTICITY ENGINEERING
2012年
2期
96-101
,共6页
付宇明%张金森%郑丽娟%张帅%杨利娜
付宇明%張金森%鄭麗娟%張帥%楊利娜
부우명%장금삼%정려연%장수%양리나
连铸辊%温度场%移动载荷%激光强化
連鑄輥%溫度場%移動載荷%激光彊化
련주곤%온도장%이동재하%격광강화
通过理论计算,得出连铸机拉矫辊辊子内外表面的温度分布;利用有限元软件建立二维拉矫辊有限元模型,采用ANSYS软件结合APDL编程实现动态热载荷的加载,解决连铸过程中旋转载荷的边界问题,从数值角度得到了拉矫辊的温度场分布.将理论结果与数值分析结果相比较,两者沿径向分布规律一致,呈对数曲线分布,最高温度存在一定差距,误差为6.06%,所得结果为正确分析辊子损伤机理奠定了基础;采用激光熔覆技术,在与辊子材料相同的试件表面涂覆Ni45合金粉末,熔覆层厚度为3mm.研究结果表明,激光熔覆技术可有效的对辊子表面进行改性,其硬度提高了近1倍.
通過理論計算,得齣連鑄機拉矯輥輥子內外錶麵的溫度分佈;利用有限元軟件建立二維拉矯輥有限元模型,採用ANSYS軟件結閤APDL編程實現動態熱載荷的加載,解決連鑄過程中鏇轉載荷的邊界問題,從數值角度得到瞭拉矯輥的溫度場分佈.將理論結果與數值分析結果相比較,兩者沿徑嚮分佈規律一緻,呈對數麯線分佈,最高溫度存在一定差距,誤差為6.06%,所得結果為正確分析輥子損傷機理奠定瞭基礎;採用激光鎔覆技術,在與輥子材料相同的試件錶麵塗覆Ni45閤金粉末,鎔覆層厚度為3mm.研究結果錶明,激光鎔覆技術可有效的對輥子錶麵進行改性,其硬度提高瞭近1倍.
통과이론계산,득출련주궤랍교곤곤자내외표면적온도분포;이용유한원연건건립이유랍교곤유한원모형,채용ANSYS연건결합APDL편정실현동태열재하적가재,해결련주과정중선전재하적변계문제,종수치각도득도료랍교곤적온도장분포.장이론결과여수치분석결과상비교,량자연경향분포규률일치,정대수곡선분포,최고온도존재일정차거,오차위6.06%,소득결과위정학분석곤자손상궤리전정료기출;채용격광용복기술,재여곤자재료상동적시건표면도복Ni45합금분말,용복층후도위3mm.연구결과표명,격광용복기술가유효적대곤자표면진행개성,기경도제고료근1배.