功能材料
功能材料
공능재료
JOURNAL OF FUNCTIONAL MATERIALS
2009年
2期
338-341
,共4页
蔡羽%赵胜利%文九巴%赵崇军
蔡羽%趙勝利%文九巴%趙崇軍
채우%조성리%문구파%조숭군
纳米粉体%LiCoxMn2-Xo4%溶胶-凝胶%PAA%掺杂
納米粉體%LiCoxMn2-Xo4%溶膠-凝膠%PAA%摻雜
납미분체%LiCoxMn2-Xo4%용효-응효%PAA%참잡
采用溶胶一凝胶法并结合热处理工艺制备LiCoxMn2-xO4粉体,结合热处理工艺制备Li-LiCoxMn2-xO4粉体.利用热重一差热分析、X射线衍射、透射电镜、充放电测试等方法对前驱体的热分解行为、粉体的结构、形貌及电化学性质进行了表征,同时研究了钴掺杂量对其结构和电化学性能的影响.结果表明,直接以聚丙烯酸(PAA)为螯合剂合成了稳定的溶胶和凝胶,进一步获得了粒径分布均匀、无团聚的尖晶石LiCoxMn2-xO4纳米粉体.随着钴掺杂量的增加,晶格常数、晶粒尺寸逐渐减小,晶格畸变逐渐增大,但对尖晶石结构影响较小;LiCoxMn2-xO4粉体的放电比容量随着x值增大略有降低,但循环性能得到明显的改善.在电流密度0.1mA/cm2、截止电压3.5~4.3V时,粒径约80hm的LiCo0.1Mn1.9O4粉体首次放电比容量达135mAh/g,20次循环后的稳定放电比容量为118mAh/g,且每次容量衰减低于0.2%,具有较好的电化学性能.
採用溶膠一凝膠法併結閤熱處理工藝製備LiCoxMn2-xO4粉體,結閤熱處理工藝製備Li-LiCoxMn2-xO4粉體.利用熱重一差熱分析、X射線衍射、透射電鏡、充放電測試等方法對前驅體的熱分解行為、粉體的結構、形貌及電化學性質進行瞭錶徵,同時研究瞭鈷摻雜量對其結構和電化學性能的影響.結果錶明,直接以聚丙烯痠(PAA)為螯閤劑閤成瞭穩定的溶膠和凝膠,進一步穫得瞭粒徑分佈均勻、無糰聚的尖晶石LiCoxMn2-xO4納米粉體.隨著鈷摻雜量的增加,晶格常數、晶粒呎吋逐漸減小,晶格畸變逐漸增大,但對尖晶石結構影響較小;LiCoxMn2-xO4粉體的放電比容量隨著x值增大略有降低,但循環性能得到明顯的改善.在電流密度0.1mA/cm2、截止電壓3.5~4.3V時,粒徑約80hm的LiCo0.1Mn1.9O4粉體首次放電比容量達135mAh/g,20次循環後的穩定放電比容量為118mAh/g,且每次容量衰減低于0.2%,具有較好的電化學性能.
채용용효일응효법병결합열처리공예제비LiCoxMn2-xO4분체,결합열처리공예제비Li-LiCoxMn2-xO4분체.이용열중일차열분석、X사선연사、투사전경、충방전측시등방법대전구체적열분해행위、분체적결구、형모급전화학성질진행료표정,동시연구료고참잡량대기결구화전화학성능적영향.결과표명,직접이취병희산(PAA)위오합제합성료은정적용효화응효,진일보획득료립경분포균균、무단취적첨정석LiCoxMn2-xO4납미분체.수착고참잡량적증가,정격상수、정립척촌축점감소,정격기변축점증대,단대첨정석결구영향교소;LiCoxMn2-xO4분체적방전비용량수착x치증대략유강저,단순배성능득도명현적개선.재전류밀도0.1mA/cm2、절지전압3.5~4.3V시,립경약80hm적LiCo0.1Mn1.9O4분체수차방전비용량체135mAh/g,20차순배후적은정방전비용량위118mAh/g,차매차용량쇠감저우0.2%,구유교호적전화학성능.