宇航材料工艺
宇航材料工藝
우항재료공예
AEROSPACE MATERIALS & TECHNOLOGY
2012年
2期
61-63
,共3页
缪长礼%匡松连%张宗强%王志才
繆長禮%劻鬆連%張宗彊%王誌纔
무장례%광송련%장종강%왕지재
聚酰胺%改性%酚醛树脂%泡沫
聚酰胺%改性%酚醛樹脂%泡沫
취선알%개성%분철수지%포말
为了改善酚醛泡沫的韧性,采用聚酰胺对酚醛树脂进行了改性,并通过化学发泡法制备了不同含量聚酰胺改性酚醛泡沫,借助DSC曲线、凝胶化时间、弯曲强度、SEM照片等表征方法研究了聚酰胺对酚醛树脂及泡沫性能的影响.结果表明:聚酰胺与酚醛树脂发生了共固化反应;酚醛树脂的反应活性随着聚酰胺含量的增加逐渐降低;加入的聚酰胺有效的改善了酚醛泡沫的韧性;酚醛泡沫弯曲强度随着聚酰胺含量的增加呈现先增加后减小的趋势,当聚酰胺含量为10wt%时,弯曲强度达到最大,比未改性的提高了约81%;酚醛泡沫SEM照片显示少量聚酰胺可以改善泡沫的泡孔结构,当聚酰胺加入量为10wt%时,酚醛泡沫泡孔结构最好,泡孔大小均匀,平均直径约为400μm.
為瞭改善酚醛泡沫的韌性,採用聚酰胺對酚醛樹脂進行瞭改性,併通過化學髮泡法製備瞭不同含量聚酰胺改性酚醛泡沫,藉助DSC麯線、凝膠化時間、彎麯彊度、SEM照片等錶徵方法研究瞭聚酰胺對酚醛樹脂及泡沫性能的影響.結果錶明:聚酰胺與酚醛樹脂髮生瞭共固化反應;酚醛樹脂的反應活性隨著聚酰胺含量的增加逐漸降低;加入的聚酰胺有效的改善瞭酚醛泡沫的韌性;酚醛泡沫彎麯彊度隨著聚酰胺含量的增加呈現先增加後減小的趨勢,噹聚酰胺含量為10wt%時,彎麯彊度達到最大,比未改性的提高瞭約81%;酚醛泡沫SEM照片顯示少量聚酰胺可以改善泡沫的泡孔結構,噹聚酰胺加入量為10wt%時,酚醛泡沫泡孔結構最好,泡孔大小均勻,平均直徑約為400μm.
위료개선분철포말적인성,채용취선알대분철수지진행료개성,병통과화학발포법제비료불동함량취선알개성분철포말,차조DSC곡선、응효화시간、만곡강도、SEM조편등표정방법연구료취선알대분철수지급포말성능적영향.결과표명:취선알여분철수지발생료공고화반응;분철수지적반응활성수착취선알함량적증가축점강저;가입적취선알유효적개선료분철포말적인성;분철포말만곡강도수착취선알함량적증가정현선증가후감소적추세,당취선알함량위10wt%시,만곡강도체도최대,비미개성적제고료약81%;분철포말SEM조편현시소량취선알가이개선포말적포공결구,당취선알가입량위10wt%시,분철포말포공결구최호,포공대소균균,평균직경약위400μm.