材料保护
材料保護
재료보호
MATERIALS PROTECTION
2009年
2期
64-65,76
,共3页
刘让贤%郑英%高原%刘坚
劉讓賢%鄭英%高原%劉堅
류양현%정영%고원%류견
双辉等离子渗铬%45钢%物相%成分%显微形貌%显微硬度
雙輝等離子滲鉻%45鋼%物相%成分%顯微形貌%顯微硬度
쌍휘등리자삼락%45강%물상%성분%현미형모%현미경도
常规双辉等离子渗铬温度较高(800℃以上),能耗较大.为此,采用双辉等离子渗金属技术,在560℃下对45钢进行了表面渗铬硬化,制备出了性能良好的表面合金改性层.采用X射线衍射仪及其附带的能谱仪测定了渗层物相及成分,采用金相显微镜考察了渗层组织形貌,并采用显微硬度计检测了渗层硬度.结果表明:渗层组织由沉积层及扩散层组成;渗层表层为2~3 μm的沉积层,含铬量达到48%以上,沉积层致密并与扩散层结合紧密;内有20~25 μm的扩散层,其合铬量呈梯度分布;表面物相由Fe-Cr、Cr7C3、Cr23C6等组成;渗层表面显微硬度达600~700 HV,硬度向内呈梯度分布.
常規雙輝等離子滲鉻溫度較高(800℃以上),能耗較大.為此,採用雙輝等離子滲金屬技術,在560℃下對45鋼進行瞭錶麵滲鉻硬化,製備齣瞭性能良好的錶麵閤金改性層.採用X射線衍射儀及其附帶的能譜儀測定瞭滲層物相及成分,採用金相顯微鏡攷察瞭滲層組織形貌,併採用顯微硬度計檢測瞭滲層硬度.結果錶明:滲層組織由沉積層及擴散層組成;滲層錶層為2~3 μm的沉積層,含鉻量達到48%以上,沉積層緻密併與擴散層結閤緊密;內有20~25 μm的擴散層,其閤鉻量呈梯度分佈;錶麵物相由Fe-Cr、Cr7C3、Cr23C6等組成;滲層錶麵顯微硬度達600~700 HV,硬度嚮內呈梯度分佈.
상규쌍휘등리자삼락온도교고(800℃이상),능모교대.위차,채용쌍휘등리자삼금속기술,재560℃하대45강진행료표면삼락경화,제비출료성능량호적표면합금개성층.채용X사선연사의급기부대적능보의측정료삼층물상급성분,채용금상현미경고찰료삼층조직형모,병채용현미경도계검측료삼층경도.결과표명:삼층조직유침적층급확산층조성;삼층표층위2~3 μm적침적층,함락량체도48%이상,침적층치밀병여확산층결합긴밀;내유20~25 μm적확산층,기합락량정제도분포;표면물상유Fe-Cr、Cr7C3、Cr23C6등조성;삼층표면현미경도체600~700 HV,경도향내정제도분포.