光电工程
光電工程
광전공정
OPTO-ELECTRONIC ENGINEERING
2012年
4期
96-101
,共6页
张明%孟惠云%陈刘伟%乐孜纯
張明%孟惠雲%陳劉偉%樂孜純
장명%맹혜운%진류위%악자순
光器件%可调谐滤波器%光折变光栅%光折变动力学
光器件%可調諧濾波器%光摺變光柵%光摺變動力學
광기건%가조해려파기%광절변광책%광절변동역학
在LiNbO3单模波导上利用双光束干涉可形成光折变波导光栅,针对粗波分复用系统提出了通过实时改变双光束之间的夹角进而改变光栅间距,实现可调谐滤波的方案.利用光折变动力学理论,得到光栅调谐时间在毫秒数量级.研究发现,适当提高光强和增加杂质掺杂浓度可提高衍射效率、减少光栅初次建立时间.基于耦合波理论的数值模拟结果表明,增大光栅长度能使衍射效率提高且带宽变小,而增加折射率调制度使衍射效率提高但同时带宽变宽.在折射率调制度为8×10-5,光栅长度大于12mm时,可获得91%以上的衍射效率和小于0.08 nm的带宽.
在LiNbO3單模波導上利用雙光束榦涉可形成光摺變波導光柵,針對粗波分複用繫統提齣瞭通過實時改變雙光束之間的夾角進而改變光柵間距,實現可調諧濾波的方案.利用光摺變動力學理論,得到光柵調諧時間在毫秒數量級.研究髮現,適噹提高光彊和增加雜質摻雜濃度可提高衍射效率、減少光柵初次建立時間.基于耦閤波理論的數值模擬結果錶明,增大光柵長度能使衍射效率提高且帶寬變小,而增加摺射率調製度使衍射效率提高但同時帶寬變寬.在摺射率調製度為8×10-5,光柵長度大于12mm時,可穫得91%以上的衍射效率和小于0.08 nm的帶寬.
재LiNbO3단모파도상이용쌍광속간섭가형성광절변파도광책,침대조파분복용계통제출료통과실시개변쌍광속지간적협각진이개변광책간거,실현가조해려파적방안.이용광절변동역학이론,득도광책조해시간재호초수량급.연구발현,괄당제고광강화증가잡질참잡농도가제고연사효솔、감소광책초차건립시간.기우우합파이론적수치모의결과표명,증대광책장도능사연사효솔제고차대관변소,이증가절사솔조제도사연사효솔제고단동시대관변관.재절사솔조제도위8×10-5,광책장도대우12mm시,가획득91%이상적연사효솔화소우0.08 nm적대관.