新型炭材料
新型炭材料
신형탄재료
NEW CARBON MATERIALS
2012年
1期
74-80
,共7页
黄向东%潘祖金%黄俊伟%李强
黃嚮東%潘祖金%黃俊偉%李彊
황향동%반조금%황준위%리강
热压法%C/C复合材料%摩擦磨损%石墨
熱壓法%C/C複閤材料%摩抆磨損%石墨
열압법%C/C복합재료%마찰마손%석묵
以经表面处理的石墨、单向炭布、和沥青粉为原料,通过热压烧结制备炭布叠层C/C复合材料.考察了炭布含量对材料密度、孔隙率、弯曲强度以及摩擦磨损的影响,采用MM200摩擦磨损试验机进行了环-块摩擦磨损实验,并借助SEM表征了材料的弯曲断口和磨痕形貌.结果表明:当炭布质量分数为50%时,C/C复合材料的综合性能最好,抗弯强度为112.2MPa,密度为1.72 g/cm3,摩擦系数为0.28,磨损率为3.68×10-13 m3·N-1·m-1.弯曲实验中材料呈“假塑性”方式破坏,断口出现大量纤维的拔出.石墨相含量的增加有利于形成较好的摩擦膜,降低磨损率,保持摩擦系数稳定.
以經錶麵處理的石墨、單嚮炭佈、和瀝青粉為原料,通過熱壓燒結製備炭佈疊層C/C複閤材料.攷察瞭炭佈含量對材料密度、孔隙率、彎麯彊度以及摩抆磨損的影響,採用MM200摩抆磨損試驗機進行瞭環-塊摩抆磨損實驗,併藉助SEM錶徵瞭材料的彎麯斷口和磨痕形貌.結果錶明:噹炭佈質量分數為50%時,C/C複閤材料的綜閤性能最好,抗彎彊度為112.2MPa,密度為1.72 g/cm3,摩抆繫數為0.28,磨損率為3.68×10-13 m3·N-1·m-1.彎麯實驗中材料呈“假塑性”方式破壞,斷口齣現大量纖維的拔齣.石墨相含量的增加有利于形成較好的摩抆膜,降低磨損率,保持摩抆繫數穩定.
이경표면처리적석묵、단향탄포、화력청분위원료,통과열압소결제비탄포첩층C/C복합재료.고찰료탄포함량대재료밀도、공극솔、만곡강도이급마찰마손적영향,채용MM200마찰마손시험궤진행료배-괴마찰마손실험,병차조SEM표정료재료적만곡단구화마흔형모.결과표명:당탄포질량분수위50%시,C/C복합재료적종합성능최호,항만강도위112.2MPa,밀도위1.72 g/cm3,마찰계수위0.28,마손솔위3.68×10-13 m3·N-1·m-1.만곡실험중재료정“가소성”방식파배,단구출현대량섬유적발출.석묵상함량적증가유리우형성교호적마찰막,강저마손솔,보지마찰계수은정.