山东冶金
山東冶金
산동야금
SHANDONG METALLURY
2008年
5期
42-45
,共4页
张广建%孙蓟泉%郭衍振%王岩%胡志远
張廣建%孫薊泉%郭衍振%王巖%鬍誌遠
장엄건%손계천%곽연진%왕암%호지원
带钢%表面粗糙度%表面质量%轧辊
帶鋼%錶麵粗糙度%錶麵質量%軋輥
대강%표면조조도%표면질량%알곤
带钢表面粗糙度是由轧机成品道次工作辊表面显微几何结构的压印形成的,为了解在一个轧制周期内钢板表面随轧制长度的变化规律以及轧辊辊面、不同厚度、钢种等对粗糙度的影响,选用HOMMEL TESTER T1000粗糙度仪,对SPHC、SDC01和SDC05钢种现场测量了带钢表面粗糙度的变化.结果表明,粗糙度随轧制长度的增加,中间有两个低谷;初始辊面的粗糙度中心部分较好,遗传到带钢的宽度方向上;粗糙度随带钢厚度的增加而增加;硬度越高的钢种粗糙度越好.根据试验结果,把一个轧制周期内的粗糙度分成不同等级,制定了轧制计划,应用表明,带钢的粗糙度在0.6~1.4μm,比原来降低了0.1~0.6μm.
帶鋼錶麵粗糙度是由軋機成品道次工作輥錶麵顯微幾何結構的壓印形成的,為瞭解在一箇軋製週期內鋼闆錶麵隨軋製長度的變化規律以及軋輥輥麵、不同厚度、鋼種等對粗糙度的影響,選用HOMMEL TESTER T1000粗糙度儀,對SPHC、SDC01和SDC05鋼種現場測量瞭帶鋼錶麵粗糙度的變化.結果錶明,粗糙度隨軋製長度的增加,中間有兩箇低穀;初始輥麵的粗糙度中心部分較好,遺傳到帶鋼的寬度方嚮上;粗糙度隨帶鋼厚度的增加而增加;硬度越高的鋼種粗糙度越好.根據試驗結果,把一箇軋製週期內的粗糙度分成不同等級,製定瞭軋製計劃,應用錶明,帶鋼的粗糙度在0.6~1.4μm,比原來降低瞭0.1~0.6μm.
대강표면조조도시유알궤성품도차공작곤표면현미궤하결구적압인형성적,위료해재일개알제주기내강판표면수알제장도적변화규률이급알곤곤면、불동후도、강충등대조조도적영향,선용HOMMEL TESTER T1000조조도의,대SPHC、SDC01화SDC05강충현장측량료대강표면조조도적변화.결과표명,조조도수알제장도적증가,중간유량개저곡;초시곤면적조조도중심부분교호,유전도대강적관도방향상;조조도수대강후도적증가이증가;경도월고적강충조조도월호.근거시험결과,파일개알제주기내적조조도분성불동등급,제정료알제계화,응용표명,대강적조조도재0.6~1.4μm,비원래강저료0.1~0.6μm.