焊接学报
銲接學報
한접학보
TRANSACTIONS OF THE CHINA WELDING INSTITUTION
2002年
1期
19-22
,共4页
Cu/WCp表面复合涂层%激光熔覆%耐摩擦磨损性能
Cu/WCp錶麵複閤塗層%激光鎔覆%耐摩抆磨損性能
Cu/WCp표면복합도층%격광용복%내마찰마손성능
采用激光熔覆表面改性方法,在45号钢基体上表面熔覆Cu/WCp复合涂层.试验研究了WC含量对熔覆复合涂层的组织特点和耐摩擦磨损性能的影响规律.研究结果表明,通过调整WC的加入量可获得α-Cu固溶体+WC双相组织;当WC的加入量超过30%时,熔覆层中出现小圆点状的WC颗粒,表明WC有一定程度的熔化和溶解;Cu/WCp复合熔覆层与基体金属之间存在过渡区,其组织为钢基体+WC混合组织.采用40Cr磨轮对Cu/WCp熔覆层进行摩擦磨损试验,结果表明,WC加入量为10%时,摩擦系数与磨损量最小;采用硬质合金磨轮进行磨损试验,当WC加入量为30%时,摩擦系数最小,而加入量为10%时,磨损量较小.
採用激光鎔覆錶麵改性方法,在45號鋼基體上錶麵鎔覆Cu/WCp複閤塗層.試驗研究瞭WC含量對鎔覆複閤塗層的組織特點和耐摩抆磨損性能的影響規律.研究結果錶明,通過調整WC的加入量可穫得α-Cu固溶體+WC雙相組織;噹WC的加入量超過30%時,鎔覆層中齣現小圓點狀的WC顆粒,錶明WC有一定程度的鎔化和溶解;Cu/WCp複閤鎔覆層與基體金屬之間存在過渡區,其組織為鋼基體+WC混閤組織.採用40Cr磨輪對Cu/WCp鎔覆層進行摩抆磨損試驗,結果錶明,WC加入量為10%時,摩抆繫數與磨損量最小;採用硬質閤金磨輪進行磨損試驗,噹WC加入量為30%時,摩抆繫數最小,而加入量為10%時,磨損量較小.
채용격광용복표면개성방법,재45호강기체상표면용복Cu/WCp복합도층.시험연구료WC함량대용복복합도층적조직특점화내마찰마손성능적영향규률.연구결과표명,통과조정WC적가입량가획득α-Cu고용체+WC쌍상조직;당WC적가입량초과30%시,용복층중출현소원점상적WC과립,표명WC유일정정도적용화화용해;Cu/WCp복합용복층여기체금속지간존재과도구,기조직위강기체+WC혼합조직.채용40Cr마륜대Cu/WCp용복층진행마찰마손시험,결과표명,WC가입량위10%시,마찰계수여마손량최소;채용경질합금마륜진행마손시험,당WC가입량위30%시,마찰계수최소,이가입량위10%시,마손량교소.