江苏科技大学学报(自然科学版)
江囌科技大學學報(自然科學版)
강소과기대학학보(자연과학판)
JOURNAL OF JIANGSU UNIVERSITY OF SCIENCE AND TECHNOLOGY(NATURAL SCIENCE EDITION)
2011年
5期
432-435
,共4页
有限元法%优化模拟%残余应力%可靠性
有限元法%優化模擬%殘餘應力%可靠性
유한원법%우화모의%잔여응력%가고성
采用有限元法对陶瓷/金属钎焊焊点可靠性及材料尺寸进行了优化模拟和分析.研究结果表明:Ti板周边区域的应力明显高于中间区域,中间区域的应力较小.分析焊点应力云图发现,最大应力集中在焊点的最拐角处,说明该处有可能成为裂纹的发源地.Al板厚度为1mm时,对应焊点残余应力达到瞬时极大值,板厚度大于1 mm时,应力值明显下降.分析Ti板厚度对焊点可靠性影响的曲线,看出应力曲线具有单调递减的趋势.Ti板开孔直径曲线存在一个极大值,大约在1.2mm处,实际应用中,应尽量避开该峰值,选择对应焊点残余应力小的孔径.焊点端部余量以及挡板厚度对应的应力曲线均单调递增.
採用有限元法對陶瓷/金屬釬銲銲點可靠性及材料呎吋進行瞭優化模擬和分析.研究結果錶明:Ti闆週邊區域的應力明顯高于中間區域,中間區域的應力較小.分析銲點應力雲圖髮現,最大應力集中在銲點的最枴角處,說明該處有可能成為裂紋的髮源地.Al闆厚度為1mm時,對應銲點殘餘應力達到瞬時極大值,闆厚度大于1 mm時,應力值明顯下降.分析Ti闆厚度對銲點可靠性影響的麯線,看齣應力麯線具有單調遞減的趨勢.Ti闆開孔直徑麯線存在一箇極大值,大約在1.2mm處,實際應用中,應儘量避開該峰值,選擇對應銲點殘餘應力小的孔徑.銲點耑部餘量以及擋闆厚度對應的應力麯線均單調遞增.
채용유한원법대도자/금속천한한점가고성급재료척촌진행료우화모의화분석.연구결과표명:Ti판주변구역적응력명현고우중간구역,중간구역적응력교소.분석한점응력운도발현,최대응력집중재한점적최괴각처,설명해처유가능성위렬문적발원지.Al판후도위1mm시,대응한점잔여응력체도순시겁대치,판후도대우1 mm시,응력치명현하강.분석Ti판후도대한점가고성영향적곡선,간출응력곡선구유단조체감적추세.Ti판개공직경곡선존재일개겁대치,대약재1.2mm처,실제응용중,응진량피개해봉치,선택대응한점잔여응력소적공경.한점단부여량이급당판후도대응적응력곡선균단조체증.