黑龙江医学
黑龍江醫學
흑룡강의학
HEILONGJIANG MEDICAL JOURNAL
2010年
9期
700-702
,共3页
瓷面处理技术%陶瓷托槽%抗剪切力强度
瓷麵處理技術%陶瓷託槽%抗剪切力彊度
자면처리기술%도자탁조%항전절력강도
目的 在不同瓷面处理技术单独或联合使用,并用发光二极管进行光照的条件下,对陶瓷托槽的抗剪切强度进行比较.方法 将30个表面光滑的瓷面随机分为3组,每组10个. 每组瓷面处理如下:第1组:9.6%氢氟酸酸蚀2 min,涂布硅烷偶联剂;第2组:氧化铝颗粒喷砂,9.6%氢氟酸酸蚀2 min,涂布硅烷偶联剂;第3组:氧化铝颗粒喷砂,涂布硅烷偶联剂,用光固化树脂粘接剂将陶瓷托槽粘接于瓷面上,分别测量抗剪切强度.结果 方差分析表明组间存在显著差异(P<0.001).第3组的抗剪切强度最低(5.35±1.28,P<0.001).第1组(11.10±1.45)和第2组(10.38±1.09;P>0.05)之间没有明显差别.结论 应用氢氟酸和硅烷偶联剂处理瓷表面可获得最大的抗剪切强度.在应用氢氟酸和硅烷偶联剂之前喷砂没有增加粘接强度.
目的 在不同瓷麵處理技術單獨或聯閤使用,併用髮光二極管進行光照的條件下,對陶瓷託槽的抗剪切彊度進行比較.方法 將30箇錶麵光滑的瓷麵隨機分為3組,每組10箇. 每組瓷麵處理如下:第1組:9.6%氫氟痠痠蝕2 min,塗佈硅烷偶聯劑;第2組:氧化鋁顆粒噴砂,9.6%氫氟痠痠蝕2 min,塗佈硅烷偶聯劑;第3組:氧化鋁顆粒噴砂,塗佈硅烷偶聯劑,用光固化樹脂粘接劑將陶瓷託槽粘接于瓷麵上,分彆測量抗剪切彊度.結果 方差分析錶明組間存在顯著差異(P<0.001).第3組的抗剪切彊度最低(5.35±1.28,P<0.001).第1組(11.10±1.45)和第2組(10.38±1.09;P>0.05)之間沒有明顯差彆.結論 應用氫氟痠和硅烷偶聯劑處理瓷錶麵可穫得最大的抗剪切彊度.在應用氫氟痠和硅烷偶聯劑之前噴砂沒有增加粘接彊度.
목적 재불동자면처리기술단독혹연합사용,병용발광이겁관진행광조적조건하,대도자탁조적항전절강도진행비교.방법 장30개표면광활적자면수궤분위3조,매조10개. 매조자면처리여하:제1조:9.6%경불산산식2 min,도포규완우련제;제2조:양화려과립분사,9.6%경불산산식2 min,도포규완우련제;제3조:양화려과립분사,도포규완우련제,용광고화수지점접제장도자탁조점접우자면상,분별측량항전절강도.결과 방차분석표명조간존재현저차이(P<0.001).제3조적항전절강도최저(5.35±1.28,P<0.001).제1조(11.10±1.45)화제2조(10.38±1.09;P>0.05)지간몰유명현차별.결론 응용경불산화규완우련제처리자표면가획득최대적항전절강도.재응용경불산화규완우련제지전분사몰유증가점접강도.