电镀与涂饰
電鍍與塗飾
전도여도식
ELECTROPLATING & FINISHING
2005年
12期
12-14
,共3页
李智%吴蒙华%刘常升%崔云先%张世财
李智%吳矇華%劉常升%崔雲先%張世財
리지%오몽화%류상승%최운선%장세재
常温发黑%磷化%超声波%无硒
常溫髮黑%燐化%超聲波%無硒
상온발흑%린화%초성파%무서
介绍了一种超声波-黑磷化无硒常温发黑工艺,其发黑液配方及操作条件为:25 g/L的Zn(H2PO4)2·2H2O,40 g/L的 Zn(NO3)2·6H2O,适量NaNO2,温度25~30 ℃, pH 2.5, 时间30 min, 超声功率为200 W.通过比较磷化(伴随超声作用)后无硒常温发黑(伴随超声作用)、无超声作用下磷化后无硒常温发黑、在磷化发黑混合液中进行磷化发黑(有或无超声作用)4种实验方案,结果表明第一种实验方案制得的膜层综合性能最佳,室外放置6个月仍然乌黑、无锈蚀,且耐磨性较好.扫描电镜图显示,该膜层结构致密,表面微裂纹细小,黑度大.EDS分析表明该膜层主要由Fe, Cu, S, O, Zn, P等化学元素组成.
介紹瞭一種超聲波-黑燐化無硒常溫髮黑工藝,其髮黑液配方及操作條件為:25 g/L的Zn(H2PO4)2·2H2O,40 g/L的 Zn(NO3)2·6H2O,適量NaNO2,溫度25~30 ℃, pH 2.5, 時間30 min, 超聲功率為200 W.通過比較燐化(伴隨超聲作用)後無硒常溫髮黑(伴隨超聲作用)、無超聲作用下燐化後無硒常溫髮黑、在燐化髮黑混閤液中進行燐化髮黑(有或無超聲作用)4種實驗方案,結果錶明第一種實驗方案製得的膜層綜閤性能最佳,室外放置6箇月仍然烏黑、無鏽蝕,且耐磨性較好.掃描電鏡圖顯示,該膜層結構緻密,錶麵微裂紋細小,黑度大.EDS分析錶明該膜層主要由Fe, Cu, S, O, Zn, P等化學元素組成.
개소료일충초성파-흑린화무서상온발흑공예,기발흑액배방급조작조건위:25 g/L적Zn(H2PO4)2·2H2O,40 g/L적 Zn(NO3)2·6H2O,괄량NaNO2,온도25~30 ℃, pH 2.5, 시간30 min, 초성공솔위200 W.통과비교린화(반수초성작용)후무서상온발흑(반수초성작용)、무초성작용하린화후무서상온발흑、재린화발흑혼합액중진행린화발흑(유혹무초성작용)4충실험방안,결과표명제일충실험방안제득적막층종합성능최가,실외방치6개월잉연오흑、무수식,차내마성교호.소묘전경도현시,해막층결구치밀,표면미렬문세소,흑도대.EDS분석표명해막층주요유Fe, Cu, S, O, Zn, P등화학원소조성.