人工晶体学报
人工晶體學報
인공정체학보
2008年
6期
1551-1554
,共4页
CoTiO3%纳米粉体%凝胶燃烧法
CoTiO3%納米粉體%凝膠燃燒法
CoTiO3%납미분체%응효연소법
以乙二胺四乙酸(EDTA)、Co(NO3)2·6H2O、冰醋酸、钛酸丁酯为原料,采用溶胶-凝胶燃烧法制备得到了CoTiO3纳米粉体.先将反应物制成凝胶前驱体,然后在干燥条件下以10 ℃/min的速率升温,用TG-DAT进行表征,结果测得其热分解和晶化温度在450 ℃以上.将此前驱体在700 ℃下焙烧2 h,制备得到了CoTiO3纳米粉体.对此纳米粉体以X射线衍射(XRD)、热重分析(TG)、透射电子显微镜(TEM)、傅立叶转换红外光谱仪(FT-IR)、紫外-可见分光光度计(UV-vis)进行表征,结果表明所制备的纳米CoTiO3粉体由粒径为30~90 nm的多边形颗粒构成,平均粒径约为70 nm.
以乙二胺四乙痠(EDTA)、Co(NO3)2·6H2O、冰醋痠、鈦痠丁酯為原料,採用溶膠-凝膠燃燒法製備得到瞭CoTiO3納米粉體.先將反應物製成凝膠前驅體,然後在榦燥條件下以10 ℃/min的速率升溫,用TG-DAT進行錶徵,結果測得其熱分解和晶化溫度在450 ℃以上.將此前驅體在700 ℃下焙燒2 h,製備得到瞭CoTiO3納米粉體.對此納米粉體以X射線衍射(XRD)、熱重分析(TG)、透射電子顯微鏡(TEM)、傅立葉轉換紅外光譜儀(FT-IR)、紫外-可見分光光度計(UV-vis)進行錶徵,結果錶明所製備的納米CoTiO3粉體由粒徑為30~90 nm的多邊形顆粒構成,平均粒徑約為70 nm.
이을이알사을산(EDTA)、Co(NO3)2·6H2O、빙작산、태산정지위원료,채용용효-응효연소법제비득도료CoTiO3납미분체.선장반응물제성응효전구체,연후재간조조건하이10 ℃/min적속솔승온,용TG-DAT진행표정,결과측득기열분해화정화온도재450 ℃이상.장차전구체재700 ℃하배소2 h,제비득도료CoTiO3납미분체.대차납미분체이X사선연사(XRD)、열중분석(TG)、투사전자현미경(TEM)、부립협전환홍외광보의(FT-IR)、자외-가견분광광도계(UV-vis)진행표정,결과표명소제비적납미CoTiO3분체유립경위30~90 nm적다변형과립구성,평균립경약위70 nm.