内蒙古师范大学学报(自然科学汉文版)
內矇古師範大學學報(自然科學漢文版)
내몽고사범대학학보(자연과학한문판)
JOURNAL OF INNER MONGOLIA NORMAL UNIVERSITY(NATURAL SCIENCE EDITION)
2011年
1期
42-45
,共4页
王立娟%周炳卿%那日苏%韩兵%郝丽媛%金志欣
王立娟%週炳卿%那日囌%韓兵%郝麗媛%金誌訢
왕립연%주병경%나일소%한병%학려원%금지흔
太阳能电池%单晶硅片%表面形貌%反射率%异丙醇%碳酸钠
太暘能電池%單晶硅片%錶麵形貌%反射率%異丙醇%碳痠鈉
태양능전지%단정규편%표면형모%반사솔%이병순%탄산납
对晶向为(100)的p型单晶硅片进行表面刻蚀,制作减反射绒面.在质量分数为3%的氢氧化钠溶液中分别加入不同质量分数的异丙醇溶液,在温度为80℃、时间为40 min的条件下对单晶硅片进行刻蚀.实验结果显示,加入质量分数为8%的异丙醇溶液刻蚀的硅片表面形貌最好,在波长为700~900nm范围内能够获得较低的反射率,最佳反射率为10.42%.保持实验条件不变,在氢氧化钠-异丙醇混合液中分别加入不同质量分数的碳酸钠溶液,对单晶硅片进行刻蚀.实验结果显示,加入质量分数为0.5%的碳酸钠溶液对制作绒面的反射率影响不大,加入质量分数为0.3%的碳酸钠溶液使制作绒面的反射率大大提高,不利于制作绒面的形成.
對晶嚮為(100)的p型單晶硅片進行錶麵刻蝕,製作減反射絨麵.在質量分數為3%的氫氧化鈉溶液中分彆加入不同質量分數的異丙醇溶液,在溫度為80℃、時間為40 min的條件下對單晶硅片進行刻蝕.實驗結果顯示,加入質量分數為8%的異丙醇溶液刻蝕的硅片錶麵形貌最好,在波長為700~900nm範圍內能夠穫得較低的反射率,最佳反射率為10.42%.保持實驗條件不變,在氫氧化鈉-異丙醇混閤液中分彆加入不同質量分數的碳痠鈉溶液,對單晶硅片進行刻蝕.實驗結果顯示,加入質量分數為0.5%的碳痠鈉溶液對製作絨麵的反射率影響不大,加入質量分數為0.3%的碳痠鈉溶液使製作絨麵的反射率大大提高,不利于製作絨麵的形成.
대정향위(100)적p형단정규편진행표면각식,제작감반사융면.재질량분수위3%적경양화납용액중분별가입불동질량분수적이병순용액,재온도위80℃、시간위40 min적조건하대단정규편진행각식.실험결과현시,가입질량분수위8%적이병순용액각식적규편표면형모최호,재파장위700~900nm범위내능구획득교저적반사솔,최가반사솔위10.42%.보지실험조건불변,재경양화납-이병순혼합액중분별가입불동질량분수적탄산납용액,대단정규편진행각식.실험결과현시,가입질량분수위0.5%적탄산납용액대제작융면적반사솔영향불대,가입질량분수위0.3%적탄산납용액사제작융면적반사솔대대제고,불리우제작융면적형성.