轻金属
輕金屬
경금속
LIGHT METALS
2012年
7期
57-60
,共4页
铝合金%均匀化退火%非平衡共晶相%微观组织
鋁閤金%均勻化退火%非平衡共晶相%微觀組織
려합금%균균화퇴화%비평형공정상%미관조직
利用光学显微镜(OM)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、能谱分析(EDS)、X射线物相分析(XRD)和差示扫描量热法(DSC)研究了Al - 7.6Zn - 1.6Mg - 1.9Cu铝合金的均匀化退火制度.结果表明:Al -7.6Zn -1.6Mg - 1.9Cu合金铸态组织偏析严重,非平衡共晶相α(Al)+ Mg(AlZnCu)2沿晶界呈连续网状分布,初始回溶温度为476℃,该合金在480℃均匀化退火时发生过烧;合金经不同均匀化退火后,非平衡共晶相发生不同程度的回溶,均匀化退火温度越高,时间越长,第二相回溶越好;该合金经420℃10h +470℃24h均匀化处理后,第二相回溶充分,且析出弥散分布的Al3Zr粒子,抑制后续固溶加工过程中的再结晶,可以作为合金合理的均匀化退火制度为420℃10h+470℃24h.
利用光學顯微鏡(OM)、掃描電子顯微鏡(SEM)、透射電子顯微鏡(TEM)、能譜分析(EDS)、X射線物相分析(XRD)和差示掃描量熱法(DSC)研究瞭Al - 7.6Zn - 1.6Mg - 1.9Cu鋁閤金的均勻化退火製度.結果錶明:Al -7.6Zn -1.6Mg - 1.9Cu閤金鑄態組織偏析嚴重,非平衡共晶相α(Al)+ Mg(AlZnCu)2沿晶界呈連續網狀分佈,初始迴溶溫度為476℃,該閤金在480℃均勻化退火時髮生過燒;閤金經不同均勻化退火後,非平衡共晶相髮生不同程度的迴溶,均勻化退火溫度越高,時間越長,第二相迴溶越好;該閤金經420℃10h +470℃24h均勻化處理後,第二相迴溶充分,且析齣瀰散分佈的Al3Zr粒子,抑製後續固溶加工過程中的再結晶,可以作為閤金閤理的均勻化退火製度為420℃10h+470℃24h.
이용광학현미경(OM)、소묘전자현미경(SEM)、투사전자현미경(TEM)、능보분석(EDS)、X사선물상분석(XRD)화차시소묘량열법(DSC)연구료Al - 7.6Zn - 1.6Mg - 1.9Cu려합금적균균화퇴화제도.결과표명:Al -7.6Zn -1.6Mg - 1.9Cu합금주태조직편석엄중,비평형공정상α(Al)+ Mg(AlZnCu)2연정계정련속망상분포,초시회용온도위476℃,해합금재480℃균균화퇴화시발생과소;합금경불동균균화퇴화후,비평형공정상발생불동정도적회용,균균화퇴화온도월고,시간월장,제이상회용월호;해합금경420℃10h +470℃24h균균화처리후,제이상회용충분,차석출미산분포적Al3Zr입자,억제후속고용가공과정중적재결정,가이작위합금합리적균균화퇴화제도위420℃10h+470℃24h.