计量学报
計量學報
계량학보
ACTA METROLOGICA SINICA
2010年
1期
42-46
,共5页
计量学%休哈特控制图%计量保证方案%计量标准考核%平均值控制界限
計量學%休哈特控製圖%計量保證方案%計量標準攷覈%平均值控製界限
계량학%휴합특공제도%계량보증방안%계량표준고핵%평균치공제계한
Metrology%Shewhart control charts%Measurement assurance programs (MAP)%Examination of a measurement standard%Mean value control boundary
采用休哈特控制图的方法可以对测量过程是否处于统计控制状态进行控制.但是,对于平均值控制界限的确定则认为不妥,根本原因是,平均值控制界限依据重复性条件下所得数据的标准偏差来设置,用它来控制复现性条件下子组的平均值的波动性,由于条件不同,因此,前者不能来控制后者.依据计量保证方案(MAP)提出的控制界限的确定,是用在复现性条件下各子组的平均值的组间标准差来设置控制界限,也就是用组内平均值的分散性来控制组内平均值.通过对二等电阻、直流电压和电能表标准装置同一组试验数据进行上述两种控制图的制作比较,以及对确定控制界限的理论分析,证明了休哈特控制图平均值控制界限的确定不妥.
採用休哈特控製圖的方法可以對測量過程是否處于統計控製狀態進行控製.但是,對于平均值控製界限的確定則認為不妥,根本原因是,平均值控製界限依據重複性條件下所得數據的標準偏差來設置,用它來控製複現性條件下子組的平均值的波動性,由于條件不同,因此,前者不能來控製後者.依據計量保證方案(MAP)提齣的控製界限的確定,是用在複現性條件下各子組的平均值的組間標準差來設置控製界限,也就是用組內平均值的分散性來控製組內平均值.通過對二等電阻、直流電壓和電能錶標準裝置同一組試驗數據進行上述兩種控製圖的製作比較,以及對確定控製界限的理論分析,證明瞭休哈特控製圖平均值控製界限的確定不妥.
채용휴합특공제도적방법가이대측량과정시부처우통계공제상태진행공제.단시,대우평균치공제계한적학정칙인위불타,근본원인시,평균치공제계한의거중복성조건하소득수거적표준편차래설치,용타래공제복현성조건하자조적평균치적파동성,유우조건불동,인차,전자불능래공제후자.의거계량보증방안(MAP)제출적공제계한적학정,시용재복현성조건하각자조적평균치적조간표준차래설치공제계한,야취시용조내평균치적분산성래공제조내평균치.통과대이등전조、직류전압화전능표표준장치동일조시험수거진행상술량충공제도적제작비교,이급대학정공제계한적이론분석,증명료휴합특공제도평균치공제계한적학정불타.
The Shewhart control chart can be used to control the measuring process whether it is under the state of statistical control. But it is considered that the confirmation for the control upper and lower limits of the mean value is improper. For the reason that the upper and lower control limits is established from standard deviation of measuring data under repeated conditions. And then, using it to control the mean value's variations character of sub-groups, in fact, the former cannot control subgroup variation due to the condition is different. Other way is described to confirm the upper and lower control limits which is based on measurement assurance programs(MAP). This method is to use sub-groups' standard deviation obtained from repeated conditions to setting the control limits, i.e. the dispersion of mean value within the subgroup to control the mean value. It has proved that the determination of the mean value controlling boundary via Shewhart control chart is improper by means of comparing the Shewhart with MAP method during analyzing the same experimental data of the DC resistance, DC voltage and electricity meter test equipments.