光学精密工程
光學精密工程
광학정밀공정
OPTICS AND PRECISION ENGINEERING
2012年
8期
1759-1764
,共6页
夏毅敏%张刚强%罗松保%张建明
夏毅敏%張剛彊%囉鬆保%張建明
하의민%장강강%라송보%장건명
非球面超精密机床%液体静压轴承%油膜%温度场%数值模拟
非毬麵超精密機床%液體靜壓軸承%油膜%溫度場%數值模擬
비구면초정밀궤상%액체정압축승%유막%온도장%수치모의
利用ANSYS CFX流体力学分析软件建立了不同油膜厚度下的液体静压轴承流体模型,研究了非球面超精密加工机床液体静压推力轴承的温度场分布.对静压推力轴承进行了试验研究,获得了工作台上不加负载、加300 kg负载、加500 kg负载3种情况下主轴性能各参数.仿真结果表明:油腔区域初始温度为20℃,从封油边开始温度逐渐升高,其中外侧的温度要比内侧温度稍高;当油膜厚度为33μm时,最高温度为20.29℃,当油膜厚度为23 μm时,最高温度为21.72℃,油膜厚度越薄,温度越高.试验计算值与仿真值分别相差3.33%、8.33%、1.32%,证实了液体静压推力轴承设计和数值计算的正确性.
利用ANSYS CFX流體力學分析軟件建立瞭不同油膜厚度下的液體靜壓軸承流體模型,研究瞭非毬麵超精密加工機床液體靜壓推力軸承的溫度場分佈.對靜壓推力軸承進行瞭試驗研究,穫得瞭工作檯上不加負載、加300 kg負載、加500 kg負載3種情況下主軸性能各參數.倣真結果錶明:油腔區域初始溫度為20℃,從封油邊開始溫度逐漸升高,其中外側的溫度要比內側溫度稍高;噹油膜厚度為33μm時,最高溫度為20.29℃,噹油膜厚度為23 μm時,最高溫度為21.72℃,油膜厚度越薄,溫度越高.試驗計算值與倣真值分彆相差3.33%、8.33%、1.32%,證實瞭液體靜壓推力軸承設計和數值計算的正確性.
이용ANSYS CFX류체역학분석연건건립료불동유막후도하적액체정압축승류체모형,연구료비구면초정밀가공궤상액체정압추력축승적온도장분포.대정압추력축승진행료시험연구,획득료공작태상불가부재、가300 kg부재、가500 kg부재3충정황하주축성능각삼수.방진결과표명:유강구역초시온도위20℃,종봉유변개시온도축점승고,기중외측적온도요비내측온도초고;당유막후도위33μm시,최고온도위20.29℃,당유막후도위23 μm시,최고온도위21.72℃,유막후도월박,온도월고.시험계산치여방진치분별상차3.33%、8.33%、1.32%,증실료액체정압추력축승설계화수치계산적정학성.