电子设计工程
電子設計工程
전자설계공정
ELECTRONIC DESIGN ENGINEERING
2011年
18期
68-70
,共3页
刘木%黄知超%钟奕%范兴明%杨升振
劉木%黃知超%鐘奕%範興明%楊升振
류목%황지초%종혁%범흥명%양승진
梯度方向角%Hough变换%分层预处理%圆检测
梯度方嚮角%Hough變換%分層預處理%圓檢測
제도방향각%Hough변환%분층예처리%원검측
gradient direction angle%hough transform%layered pretreatment%round detection
介绍了一种改进的基于梯度方向角圆检测的方法。解决了鉴别阶段随机引入第三点造成的大量无效积累.致使运算复杂的问题。首先采用分层预处理减少参与鉴别阶段的点,然后在鉴别过程中采用新方法,无需引入第三点,利用两点若为圆直径两端点,那么两点确定的线段中点即为圆心,线段长度即为直径。以圆心为基点间隔一定角度扫描,通过线段端点与待鉴别圆的交点个数验证圆。实验结果表明,该方法计算量小,检测性能比之前者显著提高,且鲁棒性好,在多圆叠加情况下效果更加突出。
介紹瞭一種改進的基于梯度方嚮角圓檢測的方法。解決瞭鑒彆階段隨機引入第三點造成的大量無效積纍.緻使運算複雜的問題。首先採用分層預處理減少參與鑒彆階段的點,然後在鑒彆過程中採用新方法,無需引入第三點,利用兩點若為圓直徑兩耑點,那麽兩點確定的線段中點即為圓心,線段長度即為直徑。以圓心為基點間隔一定角度掃描,通過線段耑點與待鑒彆圓的交點箇數驗證圓。實驗結果錶明,該方法計算量小,檢測性能比之前者顯著提高,且魯棒性好,在多圓疊加情況下效果更加突齣。
개소료일충개진적기우제도방향각원검측적방법。해결료감별계단수궤인입제삼점조성적대량무효적루.치사운산복잡적문제。수선채용분층예처리감소삼여감별계단적점,연후재감별과정중채용신방법,무수인입제삼점,이용량점약위원직경량단점,나요량점학정적선단중점즉위원심,선단장도즉위직경。이원심위기점간격일정각도소묘,통과선단단점여대감별원적교점개수험증원。실험결과표명,해방법계산량소,검측성능비지전자현저제고,차로봉성호,재다원첩가정황하효과경가돌출。
An improved circular detection method based on gradient direction angle was introduced in this paper. In the differential really round stage, by introducing the third point of random caused to accumulate a large number of invalid data and leave compute complex issue are resolved. Firstly layered image reduce unnecessary point, secondly use of new methods, if the two points are the circle diameter's end points, then two points determine the line whose midpoint is the center of the circle, and length of the line is the diameter. Center anchored by an interval of scan angle, through the number of the intersection which is endpoints and the image whether the conditions established. Contrast experimental results show that the new method consumes time shorter than before and has a good robustness. In many circles under the superimposition effect is more outstanding.