电工技术学报
電工技術學報
전공기술학보
TRANSACTIONS OF CHINA ELECTROTECHNICAL SOCIETY
2009年
10期
53-58
,共6页
王其亚%翟国富%程贤科%陈志君
王其亞%翟國富%程賢科%陳誌君
왕기아%적국부%정현과%진지군
正交试验设计%电磁继电器%反力特性%分断速度%关键调整参数
正交試驗設計%電磁繼電器%反力特性%分斷速度%關鍵調整參數
정교시험설계%전자계전기%반력특성%분단속도%관건조정삼수
Orthogonal experimental design%electromagnetic relay%reaction force characteristics%breaking velocity%key adjusted parameters
在电磁继电器调试阶段,调整参数的工艺控制直接影响继电器的反力特性,从而使吸、反力配合发生改变,最终影响到继电器的触点分断速度,分断速度的变化对继电器的电寿命产生重要影响.本文以调整参数(包括衔铁行程、返簧预压力矩、静合压力、触点间隙和动合超程)为因素,触点分断速度为指标,进行五因素四水平正交试验设计,分析、研究影响分断速度的关键参数.研究结果表明衔铁行程、触点间隙和动合超程为影响静合触点分断速度的关键参数,动合超程为影响动合触点分断速度的关键参数.最后在此基础上提出调整参数的优化方法.
在電磁繼電器調試階段,調整參數的工藝控製直接影響繼電器的反力特性,從而使吸、反力配閤髮生改變,最終影響到繼電器的觸點分斷速度,分斷速度的變化對繼電器的電壽命產生重要影響.本文以調整參數(包括銜鐵行程、返簧預壓力矩、靜閤壓力、觸點間隙和動閤超程)為因素,觸點分斷速度為指標,進行五因素四水平正交試驗設計,分析、研究影響分斷速度的關鍵參數.研究結果錶明銜鐵行程、觸點間隙和動閤超程為影響靜閤觸點分斷速度的關鍵參數,動閤超程為影響動閤觸點分斷速度的關鍵參數.最後在此基礎上提齣調整參數的優化方法.
재전자계전기조시계단,조정삼수적공예공제직접영향계전기적반력특성,종이사흡、반력배합발생개변,최종영향도계전기적촉점분단속도,분단속도적변화대계전기적전수명산생중요영향.본문이조정삼수(포괄함철행정、반황예압력구、정합압력、촉점간극화동합초정)위인소,촉점분단속도위지표,진행오인소사수평정교시험설계,분석、연구영향분단속도적관건삼수.연구결과표명함철행정、촉점간극화동합초정위영향정합촉점분단속도적관건삼수,동합초정위영향동합촉점분단속도적관건삼수.최후재차기출상제출조정삼수적우화방법.
On the stage of electromagnetic relay's being adjusted, the technical control of adjusted parameters directly affects relays' characteristics of reaction force, and changes the match of attractive force and reaction force. It eventually influences the breaking velocity of relay's contacts. And the change of contacts' breaking velocity has a great effect on relays' electrical lifespan. Taking adjusted parameters (including armature's maximum angular displacement, initial return spring's force, normally closed contacts' force, contacts' gap and normally open contacts' over travel) as factors and breaking velocities as targets, this paper does the orthogonal experimental design of five factors and four levels, analyzes and investigates the key adjusted parameters influencing breaking velocities. The research results indicate that α_(arm_max),δ_(gap) and δ_(NO_(_contacts)) are the key factors affecting breaking velocity of NC contacts, δ_(NO_(_contacts)) is the key factor affecting breaking velocity of NO contacts. Then, based on the above work, optimum method of adjusted parameters is presented.