塑料
塑料
소료
PLASTICS
2009年
1期
83-85
,共3页
张圣博%王朝虹%蔡绪福%申开智
張聖博%王朝虹%蔡緒福%申開智
장골박%왕조홍%채서복%신개지
复合应力场%双向自增强%高密度聚乙烯%微观结构%结晶
複閤應力場%雙嚮自增彊%高密度聚乙烯%微觀結構%結晶
복합응력장%쌍향자증강%고밀도취을희%미관결구%결정
采用自制的剪切拉伸双向复合应力场挤管装置,在常规工艺条件下生产了3种双向自增强的高密度聚乙烯(HDPE)管材.当剪切套转速控制为20 r/min时,牌号为2480、HD4801EX和5421B的HDPE挤出的管材周向拉伸强度与常规挤出管材相比,依次增加24.8%、41.7%和21.5%,而轴向拉伸强度的增加幅度依次为12.7%、16.8%和10.4%.通过SEM、WAXD和DSC测试手段对HDPE(2480)试样进行微观结构分析,发现其经过复合应力场后管材内部的微观结构仍是球晶,但晶体尺寸有所减小,熔融峰升高,结晶度增大.同时,管材周、轴两向的衍射强度都增强,分子链取向有所增强.
採用自製的剪切拉伸雙嚮複閤應力場擠管裝置,在常規工藝條件下生產瞭3種雙嚮自增彊的高密度聚乙烯(HDPE)管材.噹剪切套轉速控製為20 r/min時,牌號為2480、HD4801EX和5421B的HDPE擠齣的管材週嚮拉伸彊度與常規擠齣管材相比,依次增加24.8%、41.7%和21.5%,而軸嚮拉伸彊度的增加幅度依次為12.7%、16.8%和10.4%.通過SEM、WAXD和DSC測試手段對HDPE(2480)試樣進行微觀結構分析,髮現其經過複閤應力場後管材內部的微觀結構仍是毬晶,但晶體呎吋有所減小,鎔融峰升高,結晶度增大.同時,管材週、軸兩嚮的衍射彊度都增彊,分子鏈取嚮有所增彊.
채용자제적전절랍신쌍향복합응력장제관장치,재상규공예조건하생산료3충쌍향자증강적고밀도취을희(HDPE)관재.당전절투전속공제위20 r/min시,패호위2480、HD4801EX화5421B적HDPE제출적관재주향랍신강도여상규제출관재상비,의차증가24.8%、41.7%화21.5%,이축향랍신강도적증가폭도의차위12.7%、16.8%화10.4%.통과SEM、WAXD화DSC측시수단대HDPE(2480)시양진행미관결구분석,발현기경과복합응력장후관재내부적미관결구잉시구정,단정체척촌유소감소,용융봉승고,결정도증대.동시,관재주、축량향적연사강도도증강,분자련취향유소증강.