高电压技术
高電壓技術
고전압기술
HIGH VOLTAGE ENGINEERING
2008年
10期
2228-2233
,共6页
付勋波%鄂春良%李建林%许洪华
付勛波%鄂春良%李建林%許洪華
부훈파%악춘량%리건림%허홍화
直驱%并网逆变器%并联运行%零序环流(ZSCC)%零矢量%全功率
直驅%併網逆變器%併聯運行%零序環流(ZSCC)%零矢量%全功率
직구%병망역변기%병련운행%령서배류(ZSCC)%령시량%전공솔
直接驱动型风力发电系统需要全功率变流器,三相PWM变流器并联运行为首选方案.由于直接并联时产生的零序环流会造成环流损耗甚至功率器件损坏,所以必须加以抑制.为此,深入分析了PWM变流器直接并联时环流产生的机理及采用SVM算法进行调制时零矢量对于环流的影响,并在此基础上提出了基于变化零矢量的SVM环流控制方法;在Matlab/Simulink7.1中建立了3个逆变器模块直接并联的仿真模型并给出了各逆变器的控制框图,利用s函数完成了控制算法的实现.仿真表明:这种并联方案有利于模块化设计,所提的环流控制方法可行,各逆变器模块均流较好,且能够实现电网侧有功和无功功率的独立解耦控制.
直接驅動型風力髮電繫統需要全功率變流器,三相PWM變流器併聯運行為首選方案.由于直接併聯時產生的零序環流會造成環流損耗甚至功率器件損壞,所以必鬚加以抑製.為此,深入分析瞭PWM變流器直接併聯時環流產生的機理及採用SVM算法進行調製時零矢量對于環流的影響,併在此基礎上提齣瞭基于變化零矢量的SVM環流控製方法;在Matlab/Simulink7.1中建立瞭3箇逆變器模塊直接併聯的倣真模型併給齣瞭各逆變器的控製框圖,利用s函數完成瞭控製算法的實現.倣真錶明:這種併聯方案有利于模塊化設計,所提的環流控製方法可行,各逆變器模塊均流較好,且能夠實現電網側有功和無功功率的獨立解耦控製.
직접구동형풍력발전계통수요전공솔변류기,삼상PWM변류기병련운행위수선방안.유우직접병련시산생적령서배류회조성배류손모심지공솔기건손배,소이필수가이억제.위차,심입분석료PWM변류기직접병련시배유산생적궤리급채용SVM산법진행조제시령시량대우배류적영향,병재차기출상제출료기우변화령시량적SVM배류공제방법;재Matlab/Simulink7.1중건립료3개역변기모괴직접병련적방진모형병급출료각역변기적공제광도,이용s함수완성료공제산법적실현.방진표명:저충병련방안유리우모괴화설계,소제적배류공제방법가행,각역변기모괴균류교호,차능구실현전망측유공화무공공솔적독립해우공제.