特种油气藏
特種油氣藏
특충유기장
SPECIAL OIL & GAS RESERVOIRS
2011年
1期
117-120
,共4页
范英才%蒋生健%王铁强%刘永建
範英纔%蔣生健%王鐵彊%劉永建
범영재%장생건%왕철강%류영건
蒸汽吞吐%加热井筒%重力热管%空心抽油杆%吸收地热
蒸汽吞吐%加熱井筒%重力熱管%空心抽油桿%吸收地熱
증기탄토%가열정통%중력열관%공심추유간%흡수지열
目前蒸汽吞吐井采用的电加热及热流体循环工艺,存在能耗大、运行成本高及井下作业复杂等问题.依据热管原理,将机抽井中的空心抽油杆经过加工处理,改制成具有高效传热功能的重力热管,并形成了利用抽油杆柱吸收地热加热井筒新技术.介绍了油井现场制造重力热管式抽油杆柱的操作工艺,依据辽河油区3口试验井资料,分析了该技术的适用条件及影响因素.结果表明:对于油层深度低于1 300 m、油层流体温度为100~120℃、油层条件下原油黏度小于10 000 mPa·s、周期注汽量不低于2 000 m3及产液量不低于15m3/d(最好在20m3/d以上)的蒸汽吞吐井,应用该技术可取得加热井筒的好效果.
目前蒸汽吞吐井採用的電加熱及熱流體循環工藝,存在能耗大、運行成本高及井下作業複雜等問題.依據熱管原理,將機抽井中的空心抽油桿經過加工處理,改製成具有高效傳熱功能的重力熱管,併形成瞭利用抽油桿柱吸收地熱加熱井筒新技術.介紹瞭油井現場製造重力熱管式抽油桿柱的操作工藝,依據遼河油區3口試驗井資料,分析瞭該技術的適用條件及影響因素.結果錶明:對于油層深度低于1 300 m、油層流體溫度為100~120℃、油層條件下原油黏度小于10 000 mPa·s、週期註汽量不低于2 000 m3及產液量不低于15m3/d(最好在20m3/d以上)的蒸汽吞吐井,應用該技術可取得加熱井筒的好效果.
목전증기탄토정채용적전가열급열류체순배공예,존재능모대、운행성본고급정하작업복잡등문제.의거열관원리,장궤추정중적공심추유간경과가공처리,개제성구유고효전열공능적중력열관,병형성료이용추유간주흡수지열가열정통신기술.개소료유정현장제조중력열관식추유간주적조작공예,의거료하유구3구시험정자료,분석료해기술적괄용조건급영향인소.결과표명:대우유층심도저우1 300 m、유층류체온도위100~120℃、유층조건하원유점도소우10 000 mPa·s、주기주기량불저우2 000 m3급산액량불저우15m3/d(최호재20m3/d이상)적증기탄토정,응용해기술가취득가열정통적호효과.