中国表面工程
中國錶麵工程
중국표면공정
CHINA SURFACE ENGINEERING
2010年
1期
75-79
,共5页
司洪娟%徐滨士%王海斗%马国政
司洪娟%徐濱士%王海鬥%馬國政
사홍연%서빈사%왕해두%마국정
纳米电刷镀%低温离子渗硫%真空%摩擦学性能
納米電刷鍍%低溫離子滲硫%真空%摩抆學性能
납미전쇄도%저온리자삼류%진공%마찰학성능
nano-electro-brush plating%low temperature ion sulfurizing%vacuum%tribological properties
采用纳米电刷镀技术在淬火后45钢表面制备Zn涂层,对其进行低温离子渗硫处理得到复合Zn/ZnS层.考察了该复合涂层在大气和真空环境下的减摩润滑性能.结果表明,高真空环境下,刷镀层孔隙有增多、变大现象.大气环境的摩擦试验过程中,暴露的新鲜涂层与大气中的氧作用形成氧化膜,导致磨损严重,润滑性能降低,摩擦因数在0.23左右.真空中的减磨润滑效果较好,摩擦因数相对较低,在0.18左右.
採用納米電刷鍍技術在淬火後45鋼錶麵製備Zn塗層,對其進行低溫離子滲硫處理得到複閤Zn/ZnS層.攷察瞭該複閤塗層在大氣和真空環境下的減摩潤滑性能.結果錶明,高真空環境下,刷鍍層孔隙有增多、變大現象.大氣環境的摩抆試驗過程中,暴露的新鮮塗層與大氣中的氧作用形成氧化膜,導緻磨損嚴重,潤滑性能降低,摩抆因數在0.23左右.真空中的減磨潤滑效果較好,摩抆因數相對較低,在0.18左右.
채용납미전쇄도기술재쉬화후45강표면제비Zn도층,대기진행저온리자삼류처리득도복합Zn/ZnS층.고찰료해복합도층재대기화진공배경하적감마윤활성능.결과표명,고진공배경하,쇄도층공극유증다、변대현상.대기배경적마찰시험과정중,폭로적신선도층여대기중적양작용형성양화막,도치마손엄중,윤활성능강저,마찰인수재0.23좌우.진공중적감마윤활효과교호,마찰인수상대교저,재0.18좌우.
Nano electro-brush plating was used to prepare Zn coating on the surface of quenched 1045 steel, and then the Zn coating was sulfurized to obtain Zn/ZnS composite layer. The tribological properties of the compound Zn/ZnS layer were investigated in air and vacuum atmosphere respectively. The results show that the pores of electro-brush plating layer became more and larger in high vacuum atmosphere. During the wear process in air, the exposed fresh coating acted with the oxygen in the atmosphere to generate an oxide film, resulting in the decline of lubricating property in the atmosphere. The friction coefficient in air was 0.23. In contrast, the lubricating effect in vacuum was superior, and the friction coefficient in vacuum was 0.18.