粉末冶金材料科学与工程
粉末冶金材料科學與工程
분말야금재료과학여공정
POWDER METALLURGY MATERIALS SCIENCE AND ENGINEERING
2011年
2期
180-186
,共7页
李树杰%吴莹莹%李妹芝%卢越焜%陈孝飞
李樹傑%吳瑩瑩%李妹芝%盧越焜%陳孝飛
리수걸%오형형%리매지%로월혼%진효비
陶瓷连接%聚硅氧烷(SR355)%碳化硅陶瓷%纳米Si粉
陶瓷連接%聚硅氧烷(SR355)%碳化硅陶瓷%納米Si粉
도자련접%취규양완(SR355)%탄화규도자%납미Si분
无压烧结SiC(SSiC)陶瓷是重要的高温结构材料,连接技术是扩大其应用范围的关键技术之一.将纳米Si粉添加到聚硅氧烷(SR355)中制成连接材料,通过反应成形连接工艺连接SSiC.结果表明,纳米Si粉的加入对SR355的交联固化以及裂解和结晶化过程有一定的抑制作用,并能增加其陶瓷产率,因而可减少中间层的气孔率和收缩率,有利于连接强度的提高.纳米Si粉的最佳添加量为2%(质量分数).连接温度对接头强度有显著影响,在纳米Si粉添加量为2%、连接压力为40 kPa、保温时间为30 min的条件下,当连接温度为1 100℃时,连接强度达到最大值64.7 MPa.微观结构研究显示,该试样中间层由C、O和Si元素组成,界面结合较好,Si和O元素在界面区域发生扩散,有利于提高连接强度.
無壓燒結SiC(SSiC)陶瓷是重要的高溫結構材料,連接技術是擴大其應用範圍的關鍵技術之一.將納米Si粉添加到聚硅氧烷(SR355)中製成連接材料,通過反應成形連接工藝連接SSiC.結果錶明,納米Si粉的加入對SR355的交聯固化以及裂解和結晶化過程有一定的抑製作用,併能增加其陶瓷產率,因而可減少中間層的氣孔率和收縮率,有利于連接彊度的提高.納米Si粉的最佳添加量為2%(質量分數).連接溫度對接頭彊度有顯著影響,在納米Si粉添加量為2%、連接壓力為40 kPa、保溫時間為30 min的條件下,噹連接溫度為1 100℃時,連接彊度達到最大值64.7 MPa.微觀結構研究顯示,該試樣中間層由C、O和Si元素組成,界麵結閤較好,Si和O元素在界麵區域髮生擴散,有利于提高連接彊度.
무압소결SiC(SSiC)도자시중요적고온결구재료,련접기술시확대기응용범위적관건기술지일.장납미Si분첨가도취규양완(SR355)중제성련접재료,통과반응성형련접공예련접SSiC.결과표명,납미Si분적가입대SR355적교련고화이급렬해화결정화과정유일정적억제작용,병능증가기도자산솔,인이가감소중간층적기공솔화수축솔,유리우련접강도적제고.납미Si분적최가첨가량위2%(질량분수).련접온도대접두강도유현저영향,재납미Si분첨가량위2%、련접압력위40 kPa、보온시간위30 min적조건하,당련접온도위1 100℃시,련접강도체도최대치64.7 MPa.미관결구연구현시,해시양중간층유C、O화Si원소조성,계면결합교호,Si화O원소재계면구역발생확산,유리우제고련접강도.