现代化工
現代化工
현대화공
MODERN CHEMICAL INDUSTRY
2012年
1期
61-65
,共5页
雷国元%刘志军%李陈君%周曼
雷國元%劉誌軍%李陳君%週曼
뢰국원%류지군%리진군%주만
陶瓷滤料%水合氧化锆%除磷%再生%废水处理
陶瓷濾料%水閤氧化鋯%除燐%再生%廢水處理
도자려료%수합양화고%제린%재생%폐수처리
以工业粉状废物为主要原料制备出粒径为2-4mm,孔隙率为45.93%.表观密度为1.37 g/cm3,单颗抗压强度为47.73 N的粒状陶瓷滤料,并在其上负载水合氧化锆以制备吸磷材料,考察其吸磷性能和影响因素.通过SEN、XRD和FT -IR对材料进行分析,以研究其吸磷机制.结果表明:滤料负载水合氧化锆后,质量增加了20.48%,比表面积由7.15 m2/g增大到19.35 m2/g,大孔结构为主的孔隙结构变为以介孔结构为主.吸磷主要通过其表面的羟基和磷酸根之间的离子交换实现.在30℃、pH为7时,其对磷酸根有较好的吸附能力,饱和吸附量为10.79 mg/g.其吸附等温线符合Langmiur吸附模型,吸附动力学符合二级吸附动力学模型.吸附后的滤料可在NaOH中再生,经多次“吸附-解吸”后,其吸附容量一直稳定在0.5 mg/g左右.
以工業粉狀廢物為主要原料製備齣粒徑為2-4mm,孔隙率為45.93%.錶觀密度為1.37 g/cm3,單顆抗壓彊度為47.73 N的粒狀陶瓷濾料,併在其上負載水閤氧化鋯以製備吸燐材料,攷察其吸燐性能和影響因素.通過SEN、XRD和FT -IR對材料進行分析,以研究其吸燐機製.結果錶明:濾料負載水閤氧化鋯後,質量增加瞭20.48%,比錶麵積由7.15 m2/g增大到19.35 m2/g,大孔結構為主的孔隙結構變為以介孔結構為主.吸燐主要通過其錶麵的羥基和燐痠根之間的離子交換實現.在30℃、pH為7時,其對燐痠根有較好的吸附能力,飽和吸附量為10.79 mg/g.其吸附等溫線符閤Langmiur吸附模型,吸附動力學符閤二級吸附動力學模型.吸附後的濾料可在NaOH中再生,經多次“吸附-解吸”後,其吸附容量一直穩定在0.5 mg/g左右.
이공업분상폐물위주요원료제비출립경위2-4mm,공극솔위45.93%.표관밀도위1.37 g/cm3,단과항압강도위47.73 N적립상도자려료,병재기상부재수합양화고이제비흡린재료,고찰기흡린성능화영향인소.통과SEN、XRD화FT -IR대재료진행분석,이연구기흡린궤제.결과표명:려료부재수합양화고후,질량증가료20.48%,비표면적유7.15 m2/g증대도19.35 m2/g,대공결구위주적공극결구변위이개공결구위주.흡린주요통과기표면적간기화린산근지간적리자교환실현.재30℃、pH위7시,기대린산근유교호적흡부능력,포화흡부량위10.79 mg/g.기흡부등온선부합Langmiur흡부모형,흡부동역학부합이급흡부동역학모형.흡부후적려료가재NaOH중재생,경다차“흡부-해흡”후,기흡부용량일직은정재0.5 mg/g좌우.