铸造技术
鑄造技術
주조기술
FOUNDRY TECHNOLOGY
2010年
7期
877-881
,共5页
尚金金%沈军%王灵水%刘林
尚金金%瀋軍%王靈水%劉林
상금금%침군%왕령수%류림
Pb-Sn 合金%定向凝固%流动%雀斑
Pb-Sn 閤金%定嚮凝固%流動%雀斑
Pb-Sn 합금%정향응고%류동%작반
研究了不同流动条件下Pb-Sn合金进行定向凝固时,试样中雀斑的形成特征.结果表明:在温度梯度为57 K/cm,抽拉速率为6 μm/s的条件下,石墨套厚度为15 mm时,在直径为7、12和20 mm的3种试样出现了中心雀斑;石墨套厚度为10 mm时,直径7 mm和12 mm的试样出现边缘雀斑,直径20 mm试样仍然是中心雀斑;在石墨套厚度为5 mm时全部试样均未出现雀斑;这说明强自然对流条件下试样中易出现大的中心雀斑;当加入弱强迫对流后,尺寸大的中心雀斑消失,而出现少量的边缘雀斑;在加入较强的强迫对流后,所有雀斑消失.
研究瞭不同流動條件下Pb-Sn閤金進行定嚮凝固時,試樣中雀斑的形成特徵.結果錶明:在溫度梯度為57 K/cm,抽拉速率為6 μm/s的條件下,石墨套厚度為15 mm時,在直徑為7、12和20 mm的3種試樣齣現瞭中心雀斑;石墨套厚度為10 mm時,直徑7 mm和12 mm的試樣齣現邊緣雀斑,直徑20 mm試樣仍然是中心雀斑;在石墨套厚度為5 mm時全部試樣均未齣現雀斑;這說明彊自然對流條件下試樣中易齣現大的中心雀斑;噹加入弱彊迫對流後,呎吋大的中心雀斑消失,而齣現少量的邊緣雀斑;在加入較彊的彊迫對流後,所有雀斑消失.
연구료불동류동조건하Pb-Sn합금진행정향응고시,시양중작반적형성특정.결과표명:재온도제도위57 K/cm,추랍속솔위6 μm/s적조건하,석묵투후도위15 mm시,재직경위7、12화20 mm적3충시양출현료중심작반;석묵투후도위10 mm시,직경7 mm화12 mm적시양출현변연작반,직경20 mm시양잉연시중심작반;재석묵투후도위5 mm시전부시양균미출현작반;저설명강자연대류조건하시양중역출현대적중심작반;당가입약강박대류후,척촌대적중심작반소실,이출현소량적변연작반;재가입교강적강박대류후,소유작반소실.