高校化学工程学报
高校化學工程學報
고교화학공정학보
JOURNAL OF CHEMICAL ENGINEERING OF CHINESE UNIVERSITIES
2006年
4期
576-582
,共7页
袁才登%曹建伟%缪爱花%曹同玉
袁纔登%曹建偉%繆愛花%曹同玉
원재등%조건위%무애화%조동옥
中空乳胶粒%乳液聚合%核壳乳胶粒%乳胶粒形态
中空乳膠粒%乳液聚閤%覈殼乳膠粒%乳膠粒形態
중공유효립%유액취합%핵각유효립%유효립형태
为了制得具有中空结构的聚合物微球,首先以十二烷基苯磺酸钠(SDBS)为乳化剂,在其用量低于CMC的条件下,进行甲基丙烯酸甲酯(MMA)、甲基丙烯酸(MAA)和丙烯酸丁酯(BA)的乳液聚合,制备了带羧基的种子乳胶粒.然后采用MMA、MAA和二乙烯基苯为单体进行种子乳液聚合,制备了轻度交联的带羧基的核乳胶粒.该核乳胶粒经过核-壳乳液聚合和适当的碱处理工艺就可成为具有中空结构的聚合物微球.采用粒度仪测定了乳胶粒的直径及其分布,采用TEM对乳胶粒结构形态进行了表征.研究了种子及核乳胶粒制备过程中单体加料方式、乳化剂用量及羧基单体种类等因素对聚合稳定性、乳胶粒直径及其分布以及最终的中空聚合物微球结构形态的影响,确定了制备种子及核乳胶粒的最佳工艺条件.在制备种子阶段,SDBS用量为单体总量的0.5%,采用一次性加入单体的进料工艺;在核乳胶粒制备阶段,以MAA为羧基单体,所有单体采用"饥饿式"加料,半连续补加乳化剂并使乳化剂用量为核单体总量的0.15%时可保持聚合稳定性并保证无新乳胶粒生成.
為瞭製得具有中空結構的聚閤物微毬,首先以十二烷基苯磺痠鈉(SDBS)為乳化劑,在其用量低于CMC的條件下,進行甲基丙烯痠甲酯(MMA)、甲基丙烯痠(MAA)和丙烯痠丁酯(BA)的乳液聚閤,製備瞭帶羧基的種子乳膠粒.然後採用MMA、MAA和二乙烯基苯為單體進行種子乳液聚閤,製備瞭輕度交聯的帶羧基的覈乳膠粒.該覈乳膠粒經過覈-殼乳液聚閤和適噹的堿處理工藝就可成為具有中空結構的聚閤物微毬.採用粒度儀測定瞭乳膠粒的直徑及其分佈,採用TEM對乳膠粒結構形態進行瞭錶徵.研究瞭種子及覈乳膠粒製備過程中單體加料方式、乳化劑用量及羧基單體種類等因素對聚閤穩定性、乳膠粒直徑及其分佈以及最終的中空聚閤物微毬結構形態的影響,確定瞭製備種子及覈乳膠粒的最佳工藝條件.在製備種子階段,SDBS用量為單體總量的0.5%,採用一次性加入單體的進料工藝;在覈乳膠粒製備階段,以MAA為羧基單體,所有單體採用"饑餓式"加料,半連續補加乳化劑併使乳化劑用量為覈單體總量的0.15%時可保持聚閤穩定性併保證無新乳膠粒生成.
위료제득구유중공결구적취합물미구,수선이십이완기분광산납(SDBS)위유화제,재기용량저우CMC적조건하,진행갑기병희산갑지(MMA)、갑기병희산(MAA)화병희산정지(BA)적유액취합,제비료대최기적충자유효립.연후채용MMA、MAA화이을희기분위단체진행충자유액취합,제비료경도교련적대최기적핵유효립.해핵유효립경과핵-각유액취합화괄당적감처리공예취가성위구유중공결구적취합물미구.채용립도의측정료유효립적직경급기분포,채용TEM대유효립결구형태진행료표정.연구료충자급핵유효립제비과정중단체가료방식、유화제용량급최기단체충류등인소대취합은정성、유효립직경급기분포이급최종적중공취합물미구결구형태적영향,학정료제비충자급핵유효립적최가공예조건.재제비충자계단,SDBS용량위단체총량적0.5%,채용일차성가입단체적진료공예;재핵유효립제비계단,이MAA위최기단체,소유단체채용"기아식"가료,반련속보가유화제병사유화제용량위핵단체총량적0.15%시가보지취합은정성병보증무신유효립생성.