粉末冶金技术
粉末冶金技術
분말야금기술
POWDER METALLURGY TECHNOLOGY
2008年
5期
344-349
,共6页
王双喜%刘雪敬%耿彪%耿林
王雙喜%劉雪敬%耿彪%耿林
왕쌍희%류설경%경표%경림
金刚石磨轮%铝%使用寿命
金剛石磨輪%鋁%使用壽命
금강석마륜%려%사용수명
用铝合金制备了新型结合剂金刚石磨轮,研究了烧结温度对结合剂组成分别为Al-Sn-Ti、Al-Sn-Ti-Ni-Co、Al-Sn-Ti-Ni、Al-Sn-Ni-Co的金刚石磨轮的相对密度、硬度和使用寿命的影响,观察并分析了不同结合剂在不同烧结温度下的显微组织,测试了铝基结合剂金刚石磨轮的使用性能并与树脂结合剂金刚石磨轮、铜基结合剂金剐石磨轮进行了对比.结果表明:组成为Al-Sn-Ti-Ni-Co的结合剂性能较好,最佳烧结温度为300℃左右;在300℃下烧结,结合剂组织致密,对金刚石的把持力强;在修整效果达到要求的同时,铝基结合剂金刚石磨轮的使用寿命是树脂结合剂金刚石磨轮使用寿命的2倍以上.
用鋁閤金製備瞭新型結閤劑金剛石磨輪,研究瞭燒結溫度對結閤劑組成分彆為Al-Sn-Ti、Al-Sn-Ti-Ni-Co、Al-Sn-Ti-Ni、Al-Sn-Ni-Co的金剛石磨輪的相對密度、硬度和使用壽命的影響,觀察併分析瞭不同結閤劑在不同燒結溫度下的顯微組織,測試瞭鋁基結閤劑金剛石磨輪的使用性能併與樹脂結閤劑金剛石磨輪、銅基結閤劑金剮石磨輪進行瞭對比.結果錶明:組成為Al-Sn-Ti-Ni-Co的結閤劑性能較好,最佳燒結溫度為300℃左右;在300℃下燒結,結閤劑組織緻密,對金剛石的把持力彊;在脩整效果達到要求的同時,鋁基結閤劑金剛石磨輪的使用壽命是樹脂結閤劑金剛石磨輪使用壽命的2倍以上.
용려합금제비료신형결합제금강석마륜,연구료소결온도대결합제조성분별위Al-Sn-Ti、Al-Sn-Ti-Ni-Co、Al-Sn-Ti-Ni、Al-Sn-Ni-Co적금강석마륜적상대밀도、경도화사용수명적영향,관찰병분석료불동결합제재불동소결온도하적현미조직,측시료려기결합제금강석마륜적사용성능병여수지결합제금강석마륜、동기결합제금과석마륜진행료대비.결과표명:조성위Al-Sn-Ti-Ni-Co적결합제성능교호,최가소결온도위300℃좌우;재300℃하소결,결합제조직치밀,대금강석적파지력강;재수정효과체도요구적동시,려기결합제금강석마륜적사용수명시수지결합제금강석마륜사용수명적2배이상.