耐火材料
耐火材料
내화재료
REFRACTORIES
2009年
5期
354-358
,共5页
杨燕%李林%贺智勇%杨粉荣
楊燕%李林%賀智勇%楊粉榮
양연%리림%하지용%양분영
造粒石墨%Al2O3-C造粒%低水泥氧化铝基浇注料
造粒石墨%Al2O3-C造粒%低水泥氧化鋁基澆註料
조립석묵%Al2O3-C조립%저수니양화려기요주료
分别采用成型后造粒(Al2O33-C造粒Ⅰ)以及直接造粒(Al2O3-C造粒Ⅱ)两种不同的方法对天然鳞片石墨进行处理.研究了这两种造粒石墨的加入对低水泥氧化铝基浇注料物理性能、抗氧化性能以及抗渣性能的影响.结果表明:1)石墨含量较低、热处理温度较低(110℃)时,含Al2O3-C造粒Ⅰ的试样的常温抗折强度、耐压强度均优于含Al2O3-C造粒Ⅱ的试样的;2)石墨含量较高、热处理温度较高(1 500 ℃)时,含Al2O3-C造粒Ⅰ的试样的常温抗折强度、耐压强度则不如含Al2O3-C造粒Ⅱ的试样的;3)合同种造粒石墨的试样,其石墨含量越低,抗氧化性能越好;4)石墨含量对含Al2O3-C造粒Ⅱ试样的抗渣侵蚀性影响较大,浇注料中引入Al2O3-C造粒Ⅱ比引入Al2O3-C造粒Ⅰ更有利于改善试样抗渣侵蚀性.
分彆採用成型後造粒(Al2O33-C造粒Ⅰ)以及直接造粒(Al2O3-C造粒Ⅱ)兩種不同的方法對天然鱗片石墨進行處理.研究瞭這兩種造粒石墨的加入對低水泥氧化鋁基澆註料物理性能、抗氧化性能以及抗渣性能的影響.結果錶明:1)石墨含量較低、熱處理溫度較低(110℃)時,含Al2O3-C造粒Ⅰ的試樣的常溫抗摺彊度、耐壓彊度均優于含Al2O3-C造粒Ⅱ的試樣的;2)石墨含量較高、熱處理溫度較高(1 500 ℃)時,含Al2O3-C造粒Ⅰ的試樣的常溫抗摺彊度、耐壓彊度則不如含Al2O3-C造粒Ⅱ的試樣的;3)閤同種造粒石墨的試樣,其石墨含量越低,抗氧化性能越好;4)石墨含量對含Al2O3-C造粒Ⅱ試樣的抗渣侵蝕性影響較大,澆註料中引入Al2O3-C造粒Ⅱ比引入Al2O3-C造粒Ⅰ更有利于改善試樣抗渣侵蝕性.
분별채용성형후조립(Al2O33-C조립Ⅰ)이급직접조립(Al2O3-C조립Ⅱ)량충불동적방법대천연린편석묵진행처리.연구료저량충조립석묵적가입대저수니양화려기요주료물이성능、항양화성능이급항사성능적영향.결과표명:1)석묵함량교저、열처리온도교저(110℃)시,함Al2O3-C조립Ⅰ적시양적상온항절강도、내압강도균우우함Al2O3-C조립Ⅱ적시양적;2)석묵함량교고、열처리온도교고(1 500 ℃)시,함Al2O3-C조립Ⅰ적시양적상온항절강도、내압강도칙불여함Al2O3-C조립Ⅱ적시양적;3)합동충조립석묵적시양,기석묵함량월저,항양화성능월호;4)석묵함량대함Al2O3-C조립Ⅱ시양적항사침식성영향교대,요주료중인입Al2O3-C조립Ⅱ비인입Al2O3-C조립Ⅰ경유리우개선시양항사침식성.