材料开发与应用
材料開髮與應用
재료개발여응용
DEVELOPMENT AND APPLICATION OF MATERIALS
2002年
3期
11-14
,共4页
蔡安辉%施居俯%陈召国%唐黔湘
蔡安輝%施居俯%陳召國%唐黔湘
채안휘%시거부%진소국%당검상
磷酸盐石墨铸型%中低铬白口铸铁%正交试验%铸造
燐痠鹽石墨鑄型%中低鉻白口鑄鐵%正交試驗%鑄造
린산염석묵주형%중저락백구주철%정교시험%주조
用正交试验对磷酸盐石墨铸型进行了成分设计,并应用数理统计原理对各因素的影响程度进行了分析,确定了磷酸盐石墨铸型的较佳制作工艺.结果表明,w(磷酸):w(高铝粉):w(石墨)=0.30:0.30:0.70时,混制造型后于600℃烘干40min左右,磷酸铝盐石墨铸型具有较好的力学性能,其干拉伸强度可达4.67×105Pa、干压缩强度可达22.21×105Pa.高铝粉、磷酸之比的较佳范围值为0.8~1.0.干拉伸强度(σt)、压缩强度(σc)与各种因素之间的一次关系分别为:σc(105Pa)=0.71A(%)+0.47B(%)+0.022C(℃)-0.11D(min)-23.49,σt(105Pa)=0.165A(%)+0.135B(%)+0.0051C(℃)-0.0063D(min)-7.419.磷酸盐石墨铸型的耐激冷能力较强.
用正交試驗對燐痠鹽石墨鑄型進行瞭成分設計,併應用數理統計原理對各因素的影響程度進行瞭分析,確定瞭燐痠鹽石墨鑄型的較佳製作工藝.結果錶明,w(燐痠):w(高鋁粉):w(石墨)=0.30:0.30:0.70時,混製造型後于600℃烘榦40min左右,燐痠鋁鹽石墨鑄型具有較好的力學性能,其榦拉伸彊度可達4.67×105Pa、榦壓縮彊度可達22.21×105Pa.高鋁粉、燐痠之比的較佳範圍值為0.8~1.0.榦拉伸彊度(σt)、壓縮彊度(σc)與各種因素之間的一次關繫分彆為:σc(105Pa)=0.71A(%)+0.47B(%)+0.022C(℃)-0.11D(min)-23.49,σt(105Pa)=0.165A(%)+0.135B(%)+0.0051C(℃)-0.0063D(min)-7.419.燐痠鹽石墨鑄型的耐激冷能力較彊.
용정교시험대린산염석묵주형진행료성분설계,병응용수리통계원리대각인소적영향정도진행료분석,학정료린산염석묵주형적교가제작공예.결과표명,w(린산):w(고려분):w(석묵)=0.30:0.30:0.70시,혼제조형후우600℃홍간40min좌우,린산려염석묵주형구유교호적역학성능,기간랍신강도가체4.67×105Pa、간압축강도가체22.21×105Pa.고려분、린산지비적교가범위치위0.8~1.0.간랍신강도(σt)、압축강도(σc)여각충인소지간적일차관계분별위:σc(105Pa)=0.71A(%)+0.47B(%)+0.022C(℃)-0.11D(min)-23.49,σt(105Pa)=0.165A(%)+0.135B(%)+0.0051C(℃)-0.0063D(min)-7.419.린산염석묵주형적내격랭능력교강.