中国胶粘剂
中國膠粘劑
중국효점제
CHINEA ADHESIVES
2010年
12期
6-9
,共4页
黄原胶%丙烯酰胺%响应曲面法%回归分析%方差分析
黃原膠%丙烯酰胺%響應麯麵法%迴歸分析%方差分析
황원효%병희선알%향응곡면법%회귀분석%방차분석
为优化黄原胶(XG)与丙烯酰胺(AM)接枝共聚物(XG-g-AM)的合成工艺,以产品接枝率、接枝效率的回归综合得分为指标,采用响应曲面(RS)法分析了m(AM):m(XG)比例、XG浓度和辐射总剂量(60Co-γ为辐射源)对产物接枝参数的影响,并建立了相应的预测模型;同时利用元素分析、红外光谱(FT-IR)和X射线衍射(XRD)法对接枝产物的结构进行了表征.结果表明:AM已成功接枝在XG上,并且当m(AM):m(XG)=2.9:1、XG浓度为9.8 g/L和辐射总剂量为5.9 kGγ时,相应产品的接枝率、接枝效率回归综合得分的预测值(19.95)最大;验证了最佳工艺条件下制备的产品接枝率为130.2%,平均接枝效率为80.4%,综合碍分为19.78,试验值与预测值吻合较好,说明该模型可以较好地反映综合得分与各影响因素之间的关系.
為優化黃原膠(XG)與丙烯酰胺(AM)接枝共聚物(XG-g-AM)的閤成工藝,以產品接枝率、接枝效率的迴歸綜閤得分為指標,採用響應麯麵(RS)法分析瞭m(AM):m(XG)比例、XG濃度和輻射總劑量(60Co-γ為輻射源)對產物接枝參數的影響,併建立瞭相應的預測模型;同時利用元素分析、紅外光譜(FT-IR)和X射線衍射(XRD)法對接枝產物的結構進行瞭錶徵.結果錶明:AM已成功接枝在XG上,併且噹m(AM):m(XG)=2.9:1、XG濃度為9.8 g/L和輻射總劑量為5.9 kGγ時,相應產品的接枝率、接枝效率迴歸綜閤得分的預測值(19.95)最大;驗證瞭最佳工藝條件下製備的產品接枝率為130.2%,平均接枝效率為80.4%,綜閤礙分為19.78,試驗值與預測值吻閤較好,說明該模型可以較好地反映綜閤得分與各影響因素之間的關繫.
위우화황원효(XG)여병희선알(AM)접지공취물(XG-g-AM)적합성공예,이산품접지솔、접지효솔적회귀종합득분위지표,채용향응곡면(RS)법분석료m(AM):m(XG)비례、XG농도화복사총제량(60Co-γ위복사원)대산물접지삼수적영향,병건립료상응적예측모형;동시이용원소분석、홍외광보(FT-IR)화X사선연사(XRD)법대접지산물적결구진행료표정.결과표명:AM이성공접지재XG상,병차당m(AM):m(XG)=2.9:1、XG농도위9.8 g/L화복사총제량위5.9 kGγ시,상응산품적접지솔、접지효솔회귀종합득분적예측치(19.95)최대;험증료최가공예조건하제비적산품접지솔위130.2%,평균접지효솔위80.4%,종합애분위19.78,시험치여예측치문합교호,설명해모형가이교호지반영종합득분여각영향인소지간적관계.