中国惯性技术学报
中國慣性技術學報
중국관성기술학보
JOURNAL OF CHINESE INERTIAL TECHNOLOGY
2008年
2期
240-243
,共4页
谐振式集成光学陀螺%相位调制器%波形频率失真%波形峰峰值失真
諧振式集成光學陀螺%相位調製器%波形頻率失真%波形峰峰值失真
해진식집성광학타라%상위조제기%파형빈솔실진%파형봉봉치실진
采用LiNbO3相位调制器代替移频器可以明显提高调制的稳定性,但同时会引入相位调制波形失真产生的误差.分析了在采用正弦波开环相位调制技术对光路进行调制和解调时,相位调制器波形失真与陀螺输出特性的关系.通过数值仿真计算可知,调制波形的频率失真与由此引起的标度因数误差大致成线性关系;调制波形峰峰值波动引起的标度因数误差随着失真幅度的增大而急剧增大;并且当陀螺零偏为1 (°)/s时,要求调制波形频率失真小于0.07%,峰峰值失真小于1.5%,波形频率失真的影响为峰峰值失真的20倍.因此在陀螺系统设计中应保证调制频率的稳定性.
採用LiNbO3相位調製器代替移頻器可以明顯提高調製的穩定性,但同時會引入相位調製波形失真產生的誤差.分析瞭在採用正絃波開環相位調製技術對光路進行調製和解調時,相位調製器波形失真與陀螺輸齣特性的關繫.通過數值倣真計算可知,調製波形的頻率失真與由此引起的標度因數誤差大緻成線性關繫;調製波形峰峰值波動引起的標度因數誤差隨著失真幅度的增大而急劇增大;併且噹陀螺零偏為1 (°)/s時,要求調製波形頻率失真小于0.07%,峰峰值失真小于1.5%,波形頻率失真的影響為峰峰值失真的20倍.因此在陀螺繫統設計中應保證調製頻率的穩定性.
채용LiNbO3상위조제기대체이빈기가이명현제고조제적은정성,단동시회인입상위조제파형실진산생적오차.분석료재채용정현파개배상위조제기술대광로진행조제화해조시,상위조제기파형실진여타라수출특성적관계.통과수치방진계산가지,조제파형적빈솔실진여유차인기적표도인수오차대치성선성관계;조제파형봉봉치파동인기적표도인수오차수착실진폭도적증대이급극증대;병차당타라령편위1 (°)/s시,요구조제파형빈솔실진소우0.07%,봉봉치실진소우1.5%,파형빈솔실진적영향위봉봉치실진적20배.인차재타라계통설계중응보증조제빈솔적은정성.