纤维素科学与技术
纖維素科學與技術
섬유소과학여기술
JOURNAL OF CELLULOSE SCIENCE AND TECHNOLOGY
2011年
4期
45-50
,共6页
韦黎%曹云峰%熊林根%刘祝兰
韋黎%曹雲峰%熊林根%劉祝蘭
위려%조운봉%웅림근%류축란
废报纸脱墨浆%过氧化氢%甲脒亚磺酸%漂白
廢報紙脫墨漿%過氧化氫%甲脒亞磺痠%漂白
폐보지탈묵장%과양화경%갑미아광산%표백
waste newspaper deinked pulp%hydrogen peroxide%formamidine sulphinic acid%bleaching
研究了废报纸脱墨浆过氧化氢一过氧化氢(PP)、过氧化氢-甲脒亚磺酸(PF)两段漂白工艺。结果表明,废报纸脱墨浆PP漂白中第二段过氧化氢漂白的适宜工艺条件为:浆浓20%,漂白时间2.5h,温度60℃,乙二胺四乙酸(EDTA)用量0.2%,硫酸镁用量0.05%,硅酸钠用量0.5%,过氧化氢用量4%,氢氧化钠用量0.5%,漂后浆白度71.5%(ISO);PF漂白中第二段甲脒亚磺酸漂白的适宜工艺条件为:漂白温度60℃,漂白时间40min,浆浓10%,甲脒亚磺酸(FAS)用量1.6%,NaOH用量0.8%,漂后浆白度68%(ISO)。
研究瞭廢報紙脫墨漿過氧化氫一過氧化氫(PP)、過氧化氫-甲脒亞磺痠(PF)兩段漂白工藝。結果錶明,廢報紙脫墨漿PP漂白中第二段過氧化氫漂白的適宜工藝條件為:漿濃20%,漂白時間2.5h,溫度60℃,乙二胺四乙痠(EDTA)用量0.2%,硫痠鎂用量0.05%,硅痠鈉用量0.5%,過氧化氫用量4%,氫氧化鈉用量0.5%,漂後漿白度71.5%(ISO);PF漂白中第二段甲脒亞磺痠漂白的適宜工藝條件為:漂白溫度60℃,漂白時間40min,漿濃10%,甲脒亞磺痠(FAS)用量1.6%,NaOH用量0.8%,漂後漿白度68%(ISO)。
연구료폐보지탈묵장과양화경일과양화경(PP)、과양화경-갑미아광산(PF)량단표백공예。결과표명,폐보지탈묵장PP표백중제이단과양화경표백적괄의공예조건위:장농20%,표백시간2.5h,온도60℃,을이알사을산(EDTA)용량0.2%,류산미용량0.05%,규산납용량0.5%,과양화경용량4%,경양화납용량0.5%,표후장백도71.5%(ISO);PF표백중제이단갑미아광산표백적괄의공예조건위:표백온도60℃,표백시간40min,장농10%,갑미아광산(FAS)용량1.6%,NaOH용량0.8%,표후장백도68%(ISO)。
The technology of hydrogen peroxide-hydrogen peroxide (PP) two stages bleaching and hydrogen peroxid-formamidine sulphinic acid (PF) two stages bleaching of waste newspaper deinked pulp were investigated emphatically. The results showed that the optimum bleaching conditions of the second P stage in the PP two stages bleaching were determined as follows: bleaching temperature was 60℃, with 1-1202, Na2SiO3 and NaOH dosage on oven dry pulp of 4%, 0.5%, and 0.5%. Other parameters such as pulp consistency, bleaching time, EDTA and MgSO4 dosage on oven dry pulp were kept at constant at 20%, 2.5 h, 0.2% and 0.05%, respectively. So the brightness of this bleached pulp was up to 71.5% (ISO) under the optimum condition. In addition, the optimum bleaching conditions of the second F stage in the PF two stages bleaching were pulp consistency of 10%, bleaching temperature of 60℃, bleaching time of 40 min, FAS and NaOH dosage on oven dry pulp of 1.6% and 0.8%. And then the resulting pulp was obtained with the brightness of 68% (ISO).