粉末冶金材料科学与工程
粉末冶金材料科學與工程
분말야금재료과학여공정
POWDER METALLURGY MATERIALS SCIENCE AND ENGINEERING
2012年
1期
63-68
,共6页
龙坚战%徐涛%彭文%陆必志
龍堅戰%徐濤%彭文%陸必誌
룡견전%서도%팽문%륙필지
WC-Ni3Al复合材料%反应合成%粉末冶金%性能
WC-Ni3Al複閤材料%反應閤成%粉末冶金%性能
WC-Ni3Al복합재료%반응합성%분말야금%성능
在WC粉末中直接添加Ni、Al元素粉末,通过在液相烧结过程中反应合成Ni3Al来制备WC-Ni3Al复合材料,对该材料进行组织结构观察及力学性能测定,分析铝含量对合金致密化和镍铝相形成种类的影响,并对材料的抗氧化性能进行测试.结果表明,制备的WC-Ni3Al复合材料具有圆钝的WC晶粒形貌,粘结相中除Ni3Al相外还有少量的NiAl和Ni相;铝含量对WC-Ni3Al材料致密度的影响主要与高熔点的NiAl的形成量有关.与普通WC- 15Ni硬质合金的抗弯强度(1 900 MPa)和硬度(82.6 HRA)相比,WC-15Ni3Al复合材料具有低的室温抗弯强度和高的硬度,分别为1 170 MPa和86.5 HRA.随Ni3Al含量(质量分数)从15%增加到30%,WC-30Ni3Al复合材料的室温抗弯强度增加,而硬度降低,分别为1 660MPa和81.7 HRA,其高温抗氧化性能比WC-30(Co-Ni-Cr)硬质合金提高1个数量级.
在WC粉末中直接添加Ni、Al元素粉末,通過在液相燒結過程中反應閤成Ni3Al來製備WC-Ni3Al複閤材料,對該材料進行組織結構觀察及力學性能測定,分析鋁含量對閤金緻密化和鎳鋁相形成種類的影響,併對材料的抗氧化性能進行測試.結果錶明,製備的WC-Ni3Al複閤材料具有圓鈍的WC晶粒形貌,粘結相中除Ni3Al相外還有少量的NiAl和Ni相;鋁含量對WC-Ni3Al材料緻密度的影響主要與高鎔點的NiAl的形成量有關.與普通WC- 15Ni硬質閤金的抗彎彊度(1 900 MPa)和硬度(82.6 HRA)相比,WC-15Ni3Al複閤材料具有低的室溫抗彎彊度和高的硬度,分彆為1 170 MPa和86.5 HRA.隨Ni3Al含量(質量分數)從15%增加到30%,WC-30Ni3Al複閤材料的室溫抗彎彊度增加,而硬度降低,分彆為1 660MPa和81.7 HRA,其高溫抗氧化性能比WC-30(Co-Ni-Cr)硬質閤金提高1箇數量級.
재WC분말중직접첨가Ni、Al원소분말,통과재액상소결과정중반응합성Ni3Al래제비WC-Ni3Al복합재료,대해재료진행조직결구관찰급역학성능측정,분석려함량대합금치밀화화얼려상형성충류적영향,병대재료적항양화성능진행측시.결과표명,제비적WC-Ni3Al복합재료구유원둔적WC정립형모,점결상중제Ni3Al상외환유소량적NiAl화Ni상;려함량대WC-Ni3Al재료치밀도적영향주요여고용점적NiAl적형성량유관.여보통WC- 15Ni경질합금적항만강도(1 900 MPa)화경도(82.6 HRA)상비,WC-15Ni3Al복합재료구유저적실온항만강도화고적경도,분별위1 170 MPa화86.5 HRA.수Ni3Al함량(질량분수)종15%증가도30%,WC-30Ni3Al복합재료적실온항만강도증가,이경도강저,분별위1 660MPa화81.7 HRA,기고온항양화성능비WC-30(Co-Ni-Cr)경질합금제고1개수량급.