钢铁钒钛
鋼鐵釩鈦
강철범태
2008年
1期
10-16
,共7页
Nb-Ti-IF钢%再结晶退火%显微组织%织构
Nb-Ti-IF鋼%再結晶退火%顯微組織%織構
Nb-Ti-IF강%재결정퇴화%현미조직%직구
以典型成分Nb-Ti-IF钢冷轧硬卷为研究材料,结合连续热镀锌线工艺特点,系统研究了退火工艺对试验钢组织和织构的影响.研究结果表明,退火加热温度在720 ℃以上时为完全再结晶组织,加热温度在720~840 ℃间变化时,铁素体晶粒度在10.0级左右,加热温度为880 ℃时,铁素体晶粒度为9.0级;随加热温度的升高,试验钢的硬度下降,当加热温度为920 ℃,因保温后快速冷却得到非等轴组织,虽然组织粗化,但硬度却有所提高;当加热温度为840 ℃时,保温时间在30~60 s间变化时,铁素体晶体尺寸变化较小,但当加热时间从30 s增加到45 s时,显微硬度明显降低,加热时间进一步增加到60 s时,显微硬度变化不大.试验钢退火后具有较强的{223}<110>和{114}<110>织构,且退火工艺条件对它们的影响较小,随着退火温度的升高,{554}<225>、{111}<112>和{111}<110>等组分的取向密度增加趋势较明显.
以典型成分Nb-Ti-IF鋼冷軋硬捲為研究材料,結閤連續熱鍍鋅線工藝特點,繫統研究瞭退火工藝對試驗鋼組織和織構的影響.研究結果錶明,退火加熱溫度在720 ℃以上時為完全再結晶組織,加熱溫度在720~840 ℃間變化時,鐵素體晶粒度在10.0級左右,加熱溫度為880 ℃時,鐵素體晶粒度為9.0級;隨加熱溫度的升高,試驗鋼的硬度下降,噹加熱溫度為920 ℃,因保溫後快速冷卻得到非等軸組織,雖然組織粗化,但硬度卻有所提高;噹加熱溫度為840 ℃時,保溫時間在30~60 s間變化時,鐵素體晶體呎吋變化較小,但噹加熱時間從30 s增加到45 s時,顯微硬度明顯降低,加熱時間進一步增加到60 s時,顯微硬度變化不大.試驗鋼退火後具有較彊的{223}<110>和{114}<110>織構,且退火工藝條件對它們的影響較小,隨著退火溫度的升高,{554}<225>、{111}<112>和{111}<110>等組分的取嚮密度增加趨勢較明顯.
이전형성분Nb-Ti-IF강랭알경권위연구재료,결합련속열도자선공예특점,계통연구료퇴화공예대시험강조직화직구적영향.연구결과표명,퇴화가열온도재720 ℃이상시위완전재결정조직,가열온도재720~840 ℃간변화시,철소체정립도재10.0급좌우,가열온도위880 ℃시,철소체정립도위9.0급;수가열온도적승고,시험강적경도하강,당가열온도위920 ℃,인보온후쾌속냉각득도비등축조직,수연조직조화,단경도각유소제고;당가열온도위840 ℃시,보온시간재30~60 s간변화시,철소체정체척촌변화교소,단당가열시간종30 s증가도45 s시,현미경도명현강저,가열시간진일보증가도60 s시,현미경도변화불대.시험강퇴화후구유교강적{223}<110>화{114}<110>직구,차퇴화공예조건대타문적영향교소,수착퇴화온도적승고,{554}<225>、{111}<112>화{111}<110>등조분적취향밀도증가추세교명현.