航空材料学报
航空材料學報
항공재료학보
JOURNAL OF AERONAUTICAL MATERIALS
2009年
5期
39-43
,共5页
骆宇时%韩梅%李嘉荣%赵金乾%唐定中
駱宇時%韓梅%李嘉榮%趙金乾%唐定中
락우시%한매%리가영%조금건%당정중
单晶高温合金%DD3%一级时效%热处理%蠕变性能
單晶高溫閤金%DD3%一級時效%熱處理%蠕變性能
단정고온합금%DD3%일급시효%열처리%연변성능
根据DD3合金的热分析和相分析结果,设计了以增大.γ'平均尺寸、改善γ'尺寸分布和提高析出相含量为目的的时效和固溶处理制度,进行了提高DD3单晶高温合金蠕变性能的热处理工艺研究.结果表明,增加一级高温时效处理可使γ'相尺寸明显增大;高温时效温度高于1080℃时,γ'相过分长大;1060℃/4h时效处理后,γ'相组织最优;配合在1265℃/4h的固溶处理,γ'相含量得到提高的同时,合金蠕变、拉伸性能优异.组织与性能研究证明,加入一级高温时效处理的新工艺可使DD3合金组织得到明显优化,760~1038℃范围内的蠕变性能获得显著提高.根据该结果,新的热处理工艺确定为:1265℃/4h,AC+1060℃/4h,Ac+870℃/32h.
根據DD3閤金的熱分析和相分析結果,設計瞭以增大.γ'平均呎吋、改善γ'呎吋分佈和提高析齣相含量為目的的時效和固溶處理製度,進行瞭提高DD3單晶高溫閤金蠕變性能的熱處理工藝研究.結果錶明,增加一級高溫時效處理可使γ'相呎吋明顯增大;高溫時效溫度高于1080℃時,γ'相過分長大;1060℃/4h時效處理後,γ'相組織最優;配閤在1265℃/4h的固溶處理,γ'相含量得到提高的同時,閤金蠕變、拉伸性能優異.組織與性能研究證明,加入一級高溫時效處理的新工藝可使DD3閤金組織得到明顯優化,760~1038℃範圍內的蠕變性能穫得顯著提高.根據該結果,新的熱處理工藝確定為:1265℃/4h,AC+1060℃/4h,Ac+870℃/32h.
근거DD3합금적열분석화상분석결과,설계료이증대.γ'평균척촌、개선γ'척촌분포화제고석출상함량위목적적시효화고용처리제도,진행료제고DD3단정고온합금연변성능적열처리공예연구.결과표명,증가일급고온시효처리가사γ'상척촌명현증대;고온시효온도고우1080℃시,γ'상과분장대;1060℃/4h시효처리후,γ'상조직최우;배합재1265℃/4h적고용처리,γ'상함량득도제고적동시,합금연변、랍신성능우이.조직여성능연구증명,가입일급고온시효처리적신공예가사DD3합금조직득도명현우화,760~1038℃범위내적연변성능획득현저제고.근거해결과,신적열처리공예학정위:1265℃/4h,AC+1060℃/4h,Ac+870℃/32h.