机械设计与研究
機械設計與研究
궤계설계여연구
MACHINE DESIGN AND RESEARCH
2010年
1期
69-71,76
,共4页
张佐营%李志%崔增柱%宋现春
張佐營%李誌%崔增柱%宋現春
장좌영%리지%최증주%송현춘
滚珠丝杠副%弹流润滑%油膜厚度%润滑状态
滾珠絲槓副%彈流潤滑%油膜厚度%潤滑狀態
곤주사강부%탄류윤활%유막후도%윤활상태
ball screw mechanism%elastohydrodynamics lubrication%film thickness%lubrication state
从Hamrock-Dowson公式和滚珠丝杠副的接触参数出发,推导了滚珠丝杠副中最小油膜厚度的计算公式,利用数值计算方法,分析了丝杠转速、润滑油粘度和接触载荷等使用参数以及接触角、螺旋升角和曲率比等设计参数对最小油膜厚度的影响.对滚珠丝杠副的润滑状态进行了判别,计算分析表明,滚珠丝杠副的润滑属于边界润滑.讨论了改善滚珠丝杠副润滑状态的途径,分析认为,设计专用润滑脂润滑单元和提高滚道表面加工质量是改善润滑状态、提高滚珠丝杠副高速性能的主要途径.
從Hamrock-Dowson公式和滾珠絲槓副的接觸參數齣髮,推導瞭滾珠絲槓副中最小油膜厚度的計算公式,利用數值計算方法,分析瞭絲槓轉速、潤滑油粘度和接觸載荷等使用參數以及接觸角、螺鏇升角和麯率比等設計參數對最小油膜厚度的影響.對滾珠絲槓副的潤滑狀態進行瞭判彆,計算分析錶明,滾珠絲槓副的潤滑屬于邊界潤滑.討論瞭改善滾珠絲槓副潤滑狀態的途徑,分析認為,設計專用潤滑脂潤滑單元和提高滾道錶麵加工質量是改善潤滑狀態、提高滾珠絲槓副高速性能的主要途徑.
종Hamrock-Dowson공식화곤주사강부적접촉삼수출발,추도료곤주사강부중최소유막후도적계산공식,이용수치계산방법,분석료사강전속、윤활유점도화접촉재하등사용삼수이급접촉각、라선승각화곡솔비등설계삼수대최소유막후도적영향.대곤주사강부적윤활상태진행료판별,계산분석표명,곤주사강부적윤활속우변계윤활.토론료개선곤주사강부윤활상태적도경,분석인위,설계전용윤활지윤활단원화제고곤도표면가공질량시개선윤활상태、제고곤주사강부고속성능적주요도경.
The formula of the thinnest lubricating oil film thickness in ball screw is induced according to the Ham-rock-Dowson expression and the contact parameters of ball screw. Based on work mentioned above, the influence of the working parameters such as the rotating speed of screw shaft,the viscosiity of lubricating oil and the contact force,and the structural parameters such as contact angle,helix angle and the curvature ratio on the thinnest lubricant oil film thickness is analyzed by numerical simulation. Through the judgment of lubricating state in ball screw,it is indicated that ball screw always runs in conditions of boundary lubrication. The ways to improving the lubricating state of ball screw are discussed. It is deemed that to design special lubricant grease unit and to improve the surface quality of ball screw groove are two effective approaches to make better lubricating state and enhance the performance of ball screw in high speed.