轻合金加工技术
輕閤金加工技術
경합금가공기술
LIGHT ALLOY FABRICATION TECHNOLOGY
2004年
8期
45-47,51
,共4页
郑祥健%李浩言%李勇%王岩
鄭祥健%李浩言%李勇%王巖
정상건%리호언%리용%왕암
7475铝合金%固溶处理%组织%性能
7475鋁閤金%固溶處理%組織%性能
7475려합금%고용처리%조직%성능
采用力学试验、金相观察和热差分析等手段,研究了固溶处理对7475合金组织和性能的影响.研究结果表明,7475合金固溶处理时,固溶温度对常温力学性能的影响比较大,其时效后的强度随着固溶温度的增加而提高(500℃内),当基体有轻微过烧时强度并不降低;7475合金挤压带材的淬火过烧温度为490℃,较佳的固溶温度为470±5℃;7475合金淬火介质的性质及转移时间是影响淬火冷却速度的重要因素,淬火水温应尽量低(小于20℃),转移时间应尽量短(小于30s),以获得高的强度;淬火至时效的停放时间对以后的时效有一定的影响,停放时间要加以控制,停放时间确定为小于4 h或大于48h.
採用力學試驗、金相觀察和熱差分析等手段,研究瞭固溶處理對7475閤金組織和性能的影響.研究結果錶明,7475閤金固溶處理時,固溶溫度對常溫力學性能的影響比較大,其時效後的彊度隨著固溶溫度的增加而提高(500℃內),噹基體有輕微過燒時彊度併不降低;7475閤金擠壓帶材的淬火過燒溫度為490℃,較佳的固溶溫度為470±5℃;7475閤金淬火介質的性質及轉移時間是影響淬火冷卻速度的重要因素,淬火水溫應儘量低(小于20℃),轉移時間應儘量短(小于30s),以穫得高的彊度;淬火至時效的停放時間對以後的時效有一定的影響,停放時間要加以控製,停放時間確定為小于4 h或大于48h.
채용역학시험、금상관찰화열차분석등수단,연구료고용처리대7475합금조직화성능적영향.연구결과표명,7475합금고용처리시,고용온도대상온역학성능적영향비교대,기시효후적강도수착고용온도적증가이제고(500℃내),당기체유경미과소시강도병불강저;7475합금제압대재적쉬화과소온도위490℃,교가적고용온도위470±5℃;7475합금쉬화개질적성질급전이시간시영향쉬화냉각속도적중요인소,쉬화수온응진량저(소우20℃),전이시간응진량단(소우30s),이획득고적강도;쉬화지시효적정방시간대이후적시효유일정적영향,정방시간요가이공제,정방시간학정위소우4 h혹대우48h.