石化技术与应用
石化技術與應用
석화기술여응용
PETROCHEMICAL TECHNOLOGY & APPLICATION
2009年
1期
20-23
,共4页
夏德强%王萍%付君善%韩晓燕%孔爱平
夏德彊%王萍%付君善%韓曉燕%孔愛平
하덕강%왕평%부군선%한효연%공애평
絮凝剂%凹凸棒%聚氯化铝%水处理
絮凝劑%凹凸棒%聚氯化鋁%水處理
서응제%요철봉%취록화려%수처리
在HCl改性凹凸棒存在下采用慢速滴碱法合成聚氯化铝(PAC),制备出了新型凹凸棒-PAC复合絮凝剂APAC.单因素实验结果表明,制备APAC的最佳工艺条件为:AlCl3浓度为0.6 mol/L,m(铝)/m(凹凸棒)为2,反应温度为80℃,反应时间为3 h,盐基度为80%,凹凸棒改性时HCl的浓度为6 moL/L.生活污水处理结果表明,最佳操作条件为:APAC溶液(质量浓度为1 g/L)用量[m(APAC溶液)/V(生活污水)]为16 mg/L,原水的pH值为8.在最佳处理条件下,生活污水浊度下降率大于99%,CODCr下降率大于80%,残余铝质量浓度为0.134 mg/L,形成的絮凝体大而密实且沉降性好.
在HCl改性凹凸棒存在下採用慢速滴堿法閤成聚氯化鋁(PAC),製備齣瞭新型凹凸棒-PAC複閤絮凝劑APAC.單因素實驗結果錶明,製備APAC的最佳工藝條件為:AlCl3濃度為0.6 mol/L,m(鋁)/m(凹凸棒)為2,反應溫度為80℃,反應時間為3 h,鹽基度為80%,凹凸棒改性時HCl的濃度為6 moL/L.生活汙水處理結果錶明,最佳操作條件為:APAC溶液(質量濃度為1 g/L)用量[m(APAC溶液)/V(生活汙水)]為16 mg/L,原水的pH值為8.在最佳處理條件下,生活汙水濁度下降率大于99%,CODCr下降率大于80%,殘餘鋁質量濃度為0.134 mg/L,形成的絮凝體大而密實且沉降性好.
재HCl개성요철봉존재하채용만속적감법합성취록화려(PAC),제비출료신형요철봉-PAC복합서응제APAC.단인소실험결과표명,제비APAC적최가공예조건위:AlCl3농도위0.6 mol/L,m(려)/m(요철봉)위2,반응온도위80℃,반응시간위3 h,염기도위80%,요철봉개성시HCl적농도위6 moL/L.생활오수처리결과표명,최가조작조건위:APAC용액(질량농도위1 g/L)용량[m(APAC용액)/V(생활오수)]위16 mg/L,원수적pH치위8.재최가처리조건하,생활오수탁도하강솔대우99%,CODCr하강솔대우80%,잔여려질량농도위0.134 mg/L,형성적서응체대이밀실차침강성호.