润滑与密封
潤滑與密封
윤활여밀봉
LUBRICATION ENGINEERING
2008年
2期
50-52,79
,共4页
李亚东%方少明%强克刚%孙磊%吴志申
李亞東%方少明%彊剋剛%孫磊%吳誌申
리아동%방소명%강극강%손뢰%오지신
火焰喷涂%PA12%摩擦磨损
火燄噴塗%PA12%摩抆磨損
화염분도%PA12%마찰마손
采用火焰喷涂法制备了聚酰胺12(PA12)涂层,利用电子拉力机、摩擦磨损试验机、红外光谱仪和差失扫描量热仪等对涂层的结构与性能进行了研究.结果表明:火焰喷涂法适宜制备聚酰胺12耐磨、防腐涂层;红外光谱分析表明聚酰胺12在火焰喷涂过程中没有发生氧化或降解反应;涂层自拉伸强度为60.35 MPa;干摩擦磨损试验表明聚酰胺12涂层具有优良的耐磨性能,涂层的摩擦磨损机制为塑性变形、疲劳磨损和粘着磨损;在100 N,100 r/min的摩擦条件下,60 min内摩擦因数为0.44,磨损量为1.40 mg.
採用火燄噴塗法製備瞭聚酰胺12(PA12)塗層,利用電子拉力機、摩抆磨損試驗機、紅外光譜儀和差失掃描量熱儀等對塗層的結構與性能進行瞭研究.結果錶明:火燄噴塗法適宜製備聚酰胺12耐磨、防腐塗層;紅外光譜分析錶明聚酰胺12在火燄噴塗過程中沒有髮生氧化或降解反應;塗層自拉伸彊度為60.35 MPa;榦摩抆磨損試驗錶明聚酰胺12塗層具有優良的耐磨性能,塗層的摩抆磨損機製為塑性變形、疲勞磨損和粘著磨損;在100 N,100 r/min的摩抆條件下,60 min內摩抆因數為0.44,磨損量為1.40 mg.
채용화염분도법제비료취선알12(PA12)도층,이용전자랍력궤、마찰마손시험궤、홍외광보의화차실소묘량열의등대도층적결구여성능진행료연구.결과표명:화염분도법괄의제비취선알12내마、방부도층;홍외광보분석표명취선알12재화염분도과정중몰유발생양화혹강해반응;도층자랍신강도위60.35 MPa;간마찰마손시험표명취선알12도층구유우량적내마성능,도층적마찰마손궤제위소성변형、피로마손화점착마손;재100 N,100 r/min적마찰조건하,60 min내마찰인수위0.44,마손량위1.40 mg.