铸造
鑄造
주조
FOUNDRY
2011年
5期
450-453
,共4页
李英民%程冬梅%刘伟华%齐万利
李英民%程鼕梅%劉偉華%齊萬利
리영민%정동매%류위화%제만리
EPS乳液%铸造粘结剂%溶解%乳化剂%改性剂
EPS乳液%鑄造粘結劑%溶解%乳化劑%改性劑
EPS유액%주조점결제%용해%유화제%개성제
研究了利用废聚苯乙烯泡沫制备铸造用EPS乳液粘结剂的方法.粘结剂采用废EPS为主要原料,通过溶解、乳化、改性等方法,制备了一种液态的粘结材料,制成的型砂可通过吹入CO,气体进行硬化.通过试验对该EPS粘结剂混合溶剂、乳化剂、改性剂等工艺参数进行了优化,并设计了最佳的制备工艺路线.结果表明,以二甲苯、丙酮、乙酸乙酯为溶剂的最佳配比为:二甲苯:丙酮:乙酸乙酯=2:2:3(体积比).采用复合乳化剂进行乳化处理,在乳化剂5%、温度为55℃下,乳化1.5 h取得较好效果.最终粘结剂在加入$3%的情况下,初强度达到0.50 MPa,终强度达到2.4 MPa.
研究瞭利用廢聚苯乙烯泡沫製備鑄造用EPS乳液粘結劑的方法.粘結劑採用廢EPS為主要原料,通過溶解、乳化、改性等方法,製備瞭一種液態的粘結材料,製成的型砂可通過吹入CO,氣體進行硬化.通過試驗對該EPS粘結劑混閤溶劑、乳化劑、改性劑等工藝參數進行瞭優化,併設計瞭最佳的製備工藝路線.結果錶明,以二甲苯、丙酮、乙痠乙酯為溶劑的最佳配比為:二甲苯:丙酮:乙痠乙酯=2:2:3(體積比).採用複閤乳化劑進行乳化處理,在乳化劑5%、溫度為55℃下,乳化1.5 h取得較好效果.最終粘結劑在加入$3%的情況下,初彊度達到0.50 MPa,終彊度達到2.4 MPa.
연구료이용폐취분을희포말제비주조용EPS유액점결제적방법.점결제채용폐EPS위주요원료,통과용해、유화、개성등방법,제비료일충액태적점결재료,제성적형사가통과취입CO,기체진행경화.통과시험대해EPS점결제혼합용제、유화제、개성제등공예삼수진행료우화,병설계료최가적제비공예로선.결과표명,이이갑분、병동、을산을지위용제적최가배비위:이갑분:병동:을산을지=2:2:3(체적비).채용복합유화제진행유화처리,재유화제5%、온도위55℃하,유화1.5 h취득교호효과.최종점결제재가입$3%적정황하,초강도체도0.50 MPa,종강도체도2.4 MPa.