热加工工艺
熱加工工藝
열가공공예
HOT WORKING TECHNOLOGY
2011年
10期
166-169
,共4页
林高用%周玉雄%邹艳明%曾菊花
林高用%週玉雄%鄒豔明%曾菊花
림고용%주옥웅%추염명%증국화
有限元分析%淬火%5CrNiMo钢%温度场%热应力场
有限元分析%淬火%5CrNiMo鋼%溫度場%熱應力場
유한원분석%쉬화%5CrNiMo강%온도장%열응력장
借助ABAQUS有限元分析软件对几何形状复杂的5CrNiMo钢挤压模具淬火过程的温度场及热应力场进行数值模拟.计算综合考虑了非线性的材料热物性参数、力学性能参数、表面换热系数及相变潜热的影响.研究表明,淬火初期,工件表面与心部仅存在较小的温差,随淬火时间的延长,该温差不断增大,淬火约5s时,该温差达到最大值,此时表面温度虽已降低到192℃,但心部温度仍高达780℃,此后该温差不断减小,淬火约460s时,工件表面和心部温度趋于与介质相同的温度(20℃);淬火过程的热应力变化在工件内外表现为不同的特点,对于表面和心部节点,其主要表现为:表面先呈拉应力后呈压应力,心部先呈压应力后呈拉应力.
藉助ABAQUS有限元分析軟件對幾何形狀複雜的5CrNiMo鋼擠壓模具淬火過程的溫度場及熱應力場進行數值模擬.計算綜閤攷慮瞭非線性的材料熱物性參數、力學性能參數、錶麵換熱繫數及相變潛熱的影響.研究錶明,淬火初期,工件錶麵與心部僅存在較小的溫差,隨淬火時間的延長,該溫差不斷增大,淬火約5s時,該溫差達到最大值,此時錶麵溫度雖已降低到192℃,但心部溫度仍高達780℃,此後該溫差不斷減小,淬火約460s時,工件錶麵和心部溫度趨于與介質相同的溫度(20℃);淬火過程的熱應力變化在工件內外錶現為不同的特點,對于錶麵和心部節點,其主要錶現為:錶麵先呈拉應力後呈壓應力,心部先呈壓應力後呈拉應力.
차조ABAQUS유한원분석연건대궤하형상복잡적5CrNiMo강제압모구쉬화과정적온도장급열응력장진행수치모의.계산종합고필료비선성적재료열물성삼수、역학성능삼수、표면환열계수급상변잠열적영향.연구표명,쉬화초기,공건표면여심부부존재교소적온차,수쉬화시간적연장,해온차불단증대,쉬화약5s시,해온차체도최대치,차시표면온도수이강저도192℃,단심부온도잉고체780℃,차후해온차불단감소,쉬화약460s시,공건표면화심부온도추우여개질상동적온도(20℃);쉬화과정적열응력변화재공건내외표현위불동적특점,대우표면화심부절점,기주요표현위:표면선정랍응력후정압응력,심부선정압응력후정랍응력.