环境科学与技术
環境科學與技術
배경과학여기술
ENVIRONMENTAL SCIENCE & TECHNOLOGY
2010年
6期
28-30,74
,共4页
曹利%凌海志%黄学敏%马广大
曹利%凌海誌%黃學敏%馬廣大
조리%릉해지%황학민%마엄대
甲苯%复合载体%Cu-Mn复合氧化物%催化燃烧
甲苯%複閤載體%Cu-Mn複閤氧化物%催化燃燒
갑분%복합재체%Cu-Mn복합양화물%최화연소
研究采用改进的溶胶-凝胶法制备了TiO2-Al2O3复合载体,并用浸渍法制备CuMnOx/TiO2-Al2O3催化剂,通过对甲苯废气催化燃烧的实验,分别考察了Cu-Mn负载量、Cu/Mn摩尔比、焙烧温度及载体对催化剂制备过程及催化剂活性的影响.实验结果表明:活性组分负载量25%,铜锰活性组分的配比Cu:Mn=1:2,焙烧温度500't2是浸渍法制备CuMnOx/TiO2-Al2O3催化剂较佳的工艺条件;XRD衍射图谱表明,500℃下铜锰尖晶石的存在是催化剂催化活性优良的主要原因;由复合载体制备的CuMnOx/TiO2-Al2O3催化剂比单一载体制备的CuMnOx/Al2O3催化剂具有更高的甲苯转化率,其T99比单一载体要低20℃以上.
研究採用改進的溶膠-凝膠法製備瞭TiO2-Al2O3複閤載體,併用浸漬法製備CuMnOx/TiO2-Al2O3催化劑,通過對甲苯廢氣催化燃燒的實驗,分彆攷察瞭Cu-Mn負載量、Cu/Mn摩爾比、焙燒溫度及載體對催化劑製備過程及催化劑活性的影響.實驗結果錶明:活性組分負載量25%,銅錳活性組分的配比Cu:Mn=1:2,焙燒溫度500't2是浸漬法製備CuMnOx/TiO2-Al2O3催化劑較佳的工藝條件;XRD衍射圖譜錶明,500℃下銅錳尖晶石的存在是催化劑催化活性優良的主要原因;由複閤載體製備的CuMnOx/TiO2-Al2O3催化劑比單一載體製備的CuMnOx/Al2O3催化劑具有更高的甲苯轉化率,其T99比單一載體要低20℃以上.
연구채용개진적용효-응효법제비료TiO2-Al2O3복합재체,병용침지법제비CuMnOx/TiO2-Al2O3최화제,통과대갑분폐기최화연소적실험,분별고찰료Cu-Mn부재량、Cu/Mn마이비、배소온도급재체대최화제제비과정급최화제활성적영향.실험결과표명:활성조분부재량25%,동맹활성조분적배비Cu:Mn=1:2,배소온도500't2시침지법제비CuMnOx/TiO2-Al2O3최화제교가적공예조건;XRD연사도보표명,500℃하동맹첨정석적존재시최화제최화활성우량적주요원인;유복합재체제비적CuMnOx/TiO2-Al2O3최화제비단일재체제비적CuMnOx/Al2O3최화제구유경고적갑분전화솔,기T99비단일재체요저20℃이상.