河北联合大学学报(自然科学版)
河北聯閤大學學報(自然科學版)
하북연합대학학보(자연과학판)
Journal of Hebei United university natural sclence edition
2012年
3期
55-58
,共4页
王春%杨国权%梁国俐%苑少强
王春%楊國權%樑國俐%苑少彊
왕춘%양국권%량국리%원소강
中碳耐磨钢%热膨胀法%CCT曲线%相变组织
中碳耐磨鋼%熱膨脹法%CCT麯線%相變組織
중탄내마강%열팽창법%CCT곡선%상변조직
以中碳耐磨钢为研究对象,通过热膨胀法测定了中碳耐磨钢CCT曲线,分析了动态冷却条件下其组织变化,结果表明当冷速小于5℃/s时得到的组织为铁素体+贝氏体,随着冷速的增加铁素体的数量减少,当冷速达到10℃/s时得到的组织为贝氏体组织,随着冷速的增加贝氏体的形态由粒状贝氏体逐渐转换为板条贝氏体,当冷却速度在15C/s~50 ℃/s之间时得到的组织为贝氏体+马氏体的组织.当冷速大于30℃/s的时候发生马氏体转变,生成的组织主要为马氏体组织.建议直接淬火工艺冷却速度15℃/s,冷却开始温度应该在800~850℃左右,而冷却结束温度在400~450℃左右.
以中碳耐磨鋼為研究對象,通過熱膨脹法測定瞭中碳耐磨鋼CCT麯線,分析瞭動態冷卻條件下其組織變化,結果錶明噹冷速小于5℃/s時得到的組織為鐵素體+貝氏體,隨著冷速的增加鐵素體的數量減少,噹冷速達到10℃/s時得到的組織為貝氏體組織,隨著冷速的增加貝氏體的形態由粒狀貝氏體逐漸轉換為闆條貝氏體,噹冷卻速度在15C/s~50 ℃/s之間時得到的組織為貝氏體+馬氏體的組織.噹冷速大于30℃/s的時候髮生馬氏體轉變,生成的組織主要為馬氏體組織.建議直接淬火工藝冷卻速度15℃/s,冷卻開始溫度應該在800~850℃左右,而冷卻結束溫度在400~450℃左右.
이중탄내마강위연구대상,통과열팽창법측정료중탄내마강CCT곡선,분석료동태냉각조건하기조직변화,결과표명당랭속소우5℃/s시득도적조직위철소체+패씨체,수착랭속적증가철소체적수량감소,당랭속체도10℃/s시득도적조직위패씨체조직,수착랭속적증가패씨체적형태유립상패씨체축점전환위판조패씨체,당냉각속도재15C/s~50 ℃/s지간시득도적조직위패씨체+마씨체적조직.당랭속대우30℃/s적시후발생마씨체전변,생성적조직주요위마씨체조직.건의직접쉬화공예냉각속도15℃/s,냉각개시온도응해재800~850℃좌우,이냉각결속온도재400~450℃좌우.