金属制品
金屬製品
금속제품
STEEL WIRE PRODUCTS
2009年
2期
21-23
,共3页
冯绍彬%李振兴%胡芳红%栗斌%徐明达
馮紹彬%李振興%鬍芳紅%慄斌%徐明達
풍소빈%리진흥%호방홍%률빈%서명체
无氰电镀黄铜%轮胎钢帘线%电流密度%辅助络合剂
無氰電鍍黃銅%輪胎鋼簾線%電流密度%輔助絡閤劑
무청전도황동%륜태강렴선%전류밀도%보조락합제
针对三步法钢丝电镀黄铜工艺复杂、冗长,维护和管理难度高,以及热扩散工序耗能高等问题,研究出一步法焦磷酸盐无氰直接电镀黄铜工艺.介绍电镀工艺配方以及测试方法,给出镀层中Cu与Zn的质量分数计算公式.通过试验得出:电流密度在0.5~1.2 A/dm2时,随着电流密度的增加,镀层中铜含量下降,锌含量不断提高.电流密度超过1.2 A/dm2时,镀层中铜含量随电流密度的提高而增加,锌含量不断减少;辅助络合剂质量浓度为60g/L时,镀层中Cu,Zn质量比基本达到60:40,满足产品结合力的要求;当起始电流密度大于临界电流密度(0.28A/dm2)时镀层结合力良好,小于0.28 A/dm2时镀层的结合力较差.试验表明,用一步法工艺配方电镀黄铜钢丝,镀层结合力好,合金成分稳定,沉积速度快,生产线容易改造,且能达到清洁生产,节能降耗的目的.
針對三步法鋼絲電鍍黃銅工藝複雜、冗長,維護和管理難度高,以及熱擴散工序耗能高等問題,研究齣一步法焦燐痠鹽無氰直接電鍍黃銅工藝.介紹電鍍工藝配方以及測試方法,給齣鍍層中Cu與Zn的質量分數計算公式.通過試驗得齣:電流密度在0.5~1.2 A/dm2時,隨著電流密度的增加,鍍層中銅含量下降,鋅含量不斷提高.電流密度超過1.2 A/dm2時,鍍層中銅含量隨電流密度的提高而增加,鋅含量不斷減少;輔助絡閤劑質量濃度為60g/L時,鍍層中Cu,Zn質量比基本達到60:40,滿足產品結閤力的要求;噹起始電流密度大于臨界電流密度(0.28A/dm2)時鍍層結閤力良好,小于0.28 A/dm2時鍍層的結閤力較差.試驗錶明,用一步法工藝配方電鍍黃銅鋼絲,鍍層結閤力好,閤金成分穩定,沉積速度快,生產線容易改造,且能達到清潔生產,節能降耗的目的.
침대삼보법강사전도황동공예복잡、용장,유호화관리난도고,이급열확산공서모능고등문제,연구출일보법초린산염무청직접전도황동공예.개소전도공예배방이급측시방법,급출도층중Cu여Zn적질량분수계산공식.통과시험득출:전류밀도재0.5~1.2 A/dm2시,수착전류밀도적증가,도층중동함량하강,자함량불단제고.전류밀도초과1.2 A/dm2시,도층중동함량수전류밀도적제고이증가,자함량불단감소;보조락합제질량농도위60g/L시,도층중Cu,Zn질량비기본체도60:40,만족산품결합력적요구;당기시전류밀도대우림계전류밀도(0.28A/dm2)시도층결합력량호,소우0.28 A/dm2시도층적결합력교차.시험표명,용일보법공예배방전도황동강사,도층결합력호,합금성분은정,침적속도쾌,생산선용역개조,차능체도청길생산,절능강모적목적.