稀有金属
稀有金屬
희유금속
CHINESE JOURNAL OF RARE METALS
2012年
3期
373-379
,共7页
袁家伟%李婷%李兴刚%张奎%郝永辉%罗广求
袁傢偉%李婷%李興剛%張奎%郝永輝%囉廣求
원가위%리정%리흥강%장규%학영휘%라엄구
Mg-Zn-Mn镁合金%均匀化热处理%扩散动力学
Mg-Zn-Mn鎂閤金%均勻化熱處理%擴散動力學
Mg-Zn-Mn미합금%균균화열처리%확산동역학
采用光学显微镜、扫描电镜、能谱分析、X射线衍射、布氏硬度测试等材料方法,研究了新型变形镁合金Mg-xZn-1Mn(x=4%,5%,6%,质量分数)的铸态合金以及均匀化热处理T4和时效处理T6后合金的显微组织、成分以及硬度的演变规律,建立ZM合金的热处理制度.并以空位扩散机制为基础,研究均匀化扩散动力学过程,建立ZM合金的均匀化扩散方程.结果表明:在ZM系列合金中,铸态组织枝晶偏析严重,晶界上有许多粗大的Mg-Zn共晶组织,Mn主要以单质形式存在于合金中.随着Zn含量的增加,合金的化合物体积分数增加,枝晶明显细化.得出3种合金合理的均匀化处理工艺分别是:ZM41为370℃×12 h;ZM51为390℃×12 h;ZM61为390℃×20h.随着Zn含量的增加,热处理的温度和时间增加.在均匀化过程中,随均匀化处理温度提高,均匀化程度越高,时效硬化效果越好.经均匀化热处理后,大部分的Mg7Zn3相溶入基体.通过扩散动力学计算得到ZM41合金的均匀化处理温度与时间的关系为0.0008/t=exp(-11609.5/T),570 K <T<670 K,由此经验公式计算得出的均匀化处理制度与实验所得结果基本吻合.
採用光學顯微鏡、掃描電鏡、能譜分析、X射線衍射、佈氏硬度測試等材料方法,研究瞭新型變形鎂閤金Mg-xZn-1Mn(x=4%,5%,6%,質量分數)的鑄態閤金以及均勻化熱處理T4和時效處理T6後閤金的顯微組織、成分以及硬度的縯變規律,建立ZM閤金的熱處理製度.併以空位擴散機製為基礎,研究均勻化擴散動力學過程,建立ZM閤金的均勻化擴散方程.結果錶明:在ZM繫列閤金中,鑄態組織枝晶偏析嚴重,晶界上有許多粗大的Mg-Zn共晶組織,Mn主要以單質形式存在于閤金中.隨著Zn含量的增加,閤金的化閤物體積分數增加,枝晶明顯細化.得齣3種閤金閤理的均勻化處理工藝分彆是:ZM41為370℃×12 h;ZM51為390℃×12 h;ZM61為390℃×20h.隨著Zn含量的增加,熱處理的溫度和時間增加.在均勻化過程中,隨均勻化處理溫度提高,均勻化程度越高,時效硬化效果越好.經均勻化熱處理後,大部分的Mg7Zn3相溶入基體.通過擴散動力學計算得到ZM41閤金的均勻化處理溫度與時間的關繫為0.0008/t=exp(-11609.5/T),570 K <T<670 K,由此經驗公式計算得齣的均勻化處理製度與實驗所得結果基本吻閤.
채용광학현미경、소묘전경、능보분석、X사선연사、포씨경도측시등재료방법,연구료신형변형미합금Mg-xZn-1Mn(x=4%,5%,6%,질량분수)적주태합금이급균균화열처리T4화시효처리T6후합금적현미조직、성분이급경도적연변규률,건립ZM합금적열처리제도.병이공위확산궤제위기출,연구균균화확산동역학과정,건립ZM합금적균균화확산방정.결과표명:재ZM계렬합금중,주태조직지정편석엄중,정계상유허다조대적Mg-Zn공정조직,Mn주요이단질형식존재우합금중.수착Zn함량적증가,합금적화합물체적분수증가,지정명현세화.득출3충합금합리적균균화처리공예분별시:ZM41위370℃×12 h;ZM51위390℃×12 h;ZM61위390℃×20h.수착Zn함량적증가,열처리적온도화시간증가.재균균화과정중,수균균화처리온도제고,균균화정도월고,시효경화효과월호.경균균화열처리후,대부분적Mg7Zn3상용입기체.통과확산동역학계산득도ZM41합금적균균화처리온도여시간적관계위0.0008/t=exp(-11609.5/T),570 K <T<670 K,유차경험공식계산득출적균균화처리제도여실험소득결과기본문합.