中国电力
中國電力
중국전력
ELECTRIC POWER
2007年
12期
77-81
,共5页
侯凡军%孙兆勇%韩小刚%孙德金
侯凡軍%孫兆勇%韓小剛%孫德金
후범군%손조용%한소강%손덕금
超临界%直流锅炉%稳压吹管
超臨界%直流鍋爐%穩壓吹管
초림계%직류과로%은압취관
结合660 MW机组超临界直流锅炉稳压吹管的工程实践,从参数选择、吹管前机组调试重点、锅炉参数控制和靶板检验等方面进行了分析.由于差压吹管系数与实际值存在较大误差,应对过热器入口的实际吹管系数进行校核,保证实际吹管系数大于1;吹管前给水和凝结水系统应冲洗合格,加装临时补水管道,补水能力应大于900t/h;为防止受热面超温,升温升压过程中给水流量应大于630t/h,调节煤水比控制分离器出口蒸汽过热度在15℃以内.同时采取燃烧器下摆、增大上部二次风量、提高给水温度等辅助措施;检验靶板时差压吹管系数应大于1.4,靶板吹扫时间为5~10 min,可保证检验结果真实可靠.
結閤660 MW機組超臨界直流鍋爐穩壓吹管的工程實踐,從參數選擇、吹管前機組調試重點、鍋爐參數控製和靶闆檢驗等方麵進行瞭分析.由于差壓吹管繫數與實際值存在較大誤差,應對過熱器入口的實際吹管繫數進行校覈,保證實際吹管繫數大于1;吹管前給水和凝結水繫統應遲洗閤格,加裝臨時補水管道,補水能力應大于900t/h;為防止受熱麵超溫,升溫升壓過程中給水流量應大于630t/h,調節煤水比控製分離器齣口蒸汽過熱度在15℃以內.同時採取燃燒器下襬、增大上部二次風量、提高給水溫度等輔助措施;檢驗靶闆時差壓吹管繫數應大于1.4,靶闆吹掃時間為5~10 min,可保證檢驗結果真實可靠.
결합660 MW궤조초림계직류과로은압취관적공정실천,종삼수선택、취관전궤조조시중점、과로삼수공제화파판검험등방면진행료분석.유우차압취관계수여실제치존재교대오차,응대과열기입구적실제취관계수진행교핵,보증실제취관계수대우1;취관전급수화응결수계통응충세합격,가장림시보수관도,보수능력응대우900t/h;위방지수열면초온,승온승압과정중급수류량응대우630t/h,조절매수비공제분리기출구증기과열도재15℃이내.동시채취연소기하파、증대상부이차풍량、제고급수온도등보조조시;검험파판시차압취관계수응대우1.4,파판취소시간위5~10 min,가보증검험결과진실가고.