热加工工艺
熱加工工藝
열가공공예
HOT WORKING TECHNOLOGY
2010年
21期
1-4
,共4页
AZ61镁合金%TIG焊%组织%力学性能
AZ61鎂閤金%TIG銲%組織%力學性能
AZ61미합금%TIG한%조직%역학성능
对3mm厚的AZ61镁合金薄板采用AZ31、AZ61两种焊丝进行TIG焊,探讨焊丝成分对焊接接头组织和性能的影响.通过光镜、扫描电镜、X-ray和力学性能测试等手段,分析了两种焊丝所焊接头的外观形貌、显微组织、焊缝析出相和力学性能等的差异.结果表明:采用这两种焊丝都能获得无明显缺陷的焊接接头,AZ61焊丝的焊缝宏观形貌优于AZ31.焊缝区组织为细小等轴晶,主要存在а-Mg和β-Mg<,12>Al<,12>两种相,热影响区组织较粗大.采用AZ31焊丝接头的焊缝区和热影响区硬度均低于母材;采用AZ61焊丝的接头与母材相比焊缝区硬度值较高而热影响区硬度较低.拉伸断裂位置均为热影响区粗晶区.
對3mm厚的AZ61鎂閤金薄闆採用AZ31、AZ61兩種銲絲進行TIG銲,探討銲絲成分對銲接接頭組織和性能的影響.通過光鏡、掃描電鏡、X-ray和力學性能測試等手段,分析瞭兩種銲絲所銲接頭的外觀形貌、顯微組織、銲縫析齣相和力學性能等的差異.結果錶明:採用這兩種銲絲都能穫得無明顯缺陷的銲接接頭,AZ61銲絲的銲縫宏觀形貌優于AZ31.銲縫區組織為細小等軸晶,主要存在а-Mg和β-Mg<,12>Al<,12>兩種相,熱影響區組織較粗大.採用AZ31銲絲接頭的銲縫區和熱影響區硬度均低于母材;採用AZ61銲絲的接頭與母材相比銲縫區硬度值較高而熱影響區硬度較低.拉伸斷裂位置均為熱影響區粗晶區.
대3mm후적AZ61미합금박판채용AZ31、AZ61량충한사진행TIG한,탐토한사성분대한접접두조직화성능적영향.통과광경、소묘전경、X-ray화역학성능측시등수단,분석료량충한사소한접두적외관형모、현미조직、한봉석출상화역학성능등적차이.결과표명:채용저량충한사도능획득무명현결함적한접접두,AZ61한사적한봉굉관형모우우AZ31.한봉구조직위세소등축정,주요존재а-Mg화β-Mg<,12>Al<,12>량충상,열영향구조직교조대.채용AZ31한사접두적한봉구화열영향구경도균저우모재;채용AZ61한사적접두여모재상비한봉구경도치교고이열영향구경도교저.랍신단렬위치균위열영향구조정구.