河北工业科技
河北工業科技
하북공업과기
HEBEI JOURNAL OF INDUSTRIAL SCIENCE & TECHNOLOGY
2010年
6期
417-420
,共4页
甲醛%室内空气%酚试剂法%条件优化
甲醛%室內空氣%酚試劑法%條件優化
갑철%실내공기%분시제법%조건우화
为了提高酚试剂法测定室内空气中甲醛的准确性,优化实验条件,系统研究了盐酸介质浓度、显色剂加入量、显色时间、显色反应温度和稀释液类型等因素对吸光度的影响,研究结果表明,采用0.1 mol/L盐酸配制的硫酸铁铵显色剂,显色剂加入量对吸光度影响不显著,最佳加入量为0.4 mL;显色反应温度对吸光度影响明显,最佳温度应控制在25~35 ℃范围内;稳定的显色反应时间应控制在18~30 min内,以20 min为宜;当甲醛质量浓度较高时,可选用去离子水或酚试剂吸收液进行适当的稀释.在较优的实验条件下,测定的甲醛质量浓度与吸光度在0~2.0 μg /mL范围内呈良好的线性关系,r=0.999 9.
為瞭提高酚試劑法測定室內空氣中甲醛的準確性,優化實驗條件,繫統研究瞭鹽痠介質濃度、顯色劑加入量、顯色時間、顯色反應溫度和稀釋液類型等因素對吸光度的影響,研究結果錶明,採用0.1 mol/L鹽痠配製的硫痠鐵銨顯色劑,顯色劑加入量對吸光度影響不顯著,最佳加入量為0.4 mL;顯色反應溫度對吸光度影響明顯,最佳溫度應控製在25~35 ℃範圍內;穩定的顯色反應時間應控製在18~30 min內,以20 min為宜;噹甲醛質量濃度較高時,可選用去離子水或酚試劑吸收液進行適噹的稀釋.在較優的實驗條件下,測定的甲醛質量濃度與吸光度在0~2.0 μg /mL範圍內呈良好的線性關繫,r=0.999 9.
위료제고분시제법측정실내공기중갑철적준학성,우화실험조건,계통연구료염산개질농도、현색제가입량、현색시간、현색반응온도화희석액류형등인소대흡광도적영향,연구결과표명,채용0.1 mol/L염산배제적류산철안현색제,현색제가입량대흡광도영향불현저,최가가입량위0.4 mL;현색반응온도대흡광도영향명현,최가온도응공제재25~35 ℃범위내;은정적현색반응시간응공제재18~30 min내,이20 min위의;당갑철질량농도교고시,가선용거리자수혹분시제흡수액진행괄당적희석.재교우적실험조건하,측정적갑철질량농도여흡광도재0~2.0 μg /mL범위내정량호적선성관계,r=0.999 9.